中英文对照：电动蝶阀的安装说明.docVIP

中英文对照：电动蝶阀的安装说明 焊接与银钎焊 SOLDERING AND SILVER BRAZING 务必记住所推荐的气动蝶阀的用途是什么，并对所应用的环境进行分析，这样才能决定选用最适合安装什么样的电动蝶阀。在安装正确的电动蝶阀之前，为了防止损坏电动蝶阀，并保证充分发挥电动蝶阀的工作性能，请阅读一下安装指南： Analyze the application to determine which valve is best suited for installations, keeping in mind the service for which the valve is recommended. Before installing the correct valve, review the installation instructions to prevent damage to the valve and to assure its maximum efficiency： 在管道的外面和焊接罩的内部涂上焊剂，焊剂必须完全覆盖焊接表面。请有节制地使用焊剂。 Apply flux to outside of tube and inside of solder cup. Surfaces to be joined must be completely covered. Use flux sparingly. 要确保电动蝶阀处于开启状态。先对管道加热。尽可能多的将热从管道传递到电动蝶阀。避免延长电动蝶阀本身的加热时间。 Be sure that valve is fully open. Apply heat to tube first. Transfer as much heat as possible through tube into valve. Avoid prolonged heating of valve itself. 先沿着垂直方向切割管道，并修整、去除毛刺，测量管径。 Cut tube end square. Ream, burr and size. 使用纱布或钢丝刷清除管道和切割部位，使其金属表面发光发亮。建议不要使用钢丝绒。 Use sand cloth or steel wire brush to clean both ends to a bright metal finish. Steel wool is not recommended. 银钎焊的方法：对需要进行钎焊的部件进行组装。如果允许涂上焊剂的部件处于直立状态，那么焊剂中的水分会蒸发掉，而干燥的焊剂很容易脱落，致使暴露的金属表面容易被氧化。在进行连接组装时，要将管道插入管套直到遇到阻挡为止。组装是要保证有稳固的支撑，使得整个钎焊操作过程中能够保持在直线位置。 Silver Brazing Method: Assemble parts to be brazed. If fluxed parts are allowed to stand, the water in the flux will evaporate, and dried flux is liable to flake off, exposing metal surfaces to oxidation. Assemble joint by inserting tube into socket hard against the stop. The assembly should be firmly supported so that it will remain in alignment during the brazing operation. 在电动蝶阀的套筒底座用火焰进行烘烤。加热要均匀，用火焰对电动蝶阀及管道进行火焰烘烤的过程要延续到电动蝶阀上的焊剂不再发出声音。不要对电动蝶阀过度加热。 Apply flame to valve at base of socket. Heat uniformly, sweeping flame from valve to tube until flux on valve becomes quiet. Avoid excessive heating of valve. 当焊剂变成液态并且在管道和电动蝶阀上呈现半透明状态时，开始将火焰沿着连接部件的轴线进行进退烘烤，以保持连接部件、特别是电动蝶阀套筒底座部位的热度。 When flux appears liquid and transparent on both tube and valve, start sweeping flame back and forth along axis of join