DM800HD问题解决.docVIP

1.启动电压低，硬件问题。 2.调谐器是错误的...防止全面启动了。 3.SIM卡与抄板机器的软件版本是否适合。 4.LM2742构成的1.3V电路（图）是为主芯片BCM7401提供的电源.为了确保供其卫星电视接收机电源的动态稳定性能,在主板卡座的上方两排8只大容量电解电容中有7只（4700μF/10V×3,2200μF/6.3V×4）为1.3V电源滤波。 5.主板上电源 6.AMD29F040 7.不插高频头可以启动吗? 高频头问题 8.三个晶振频率对吗? 频偏不能超过100K. 9.换一下解耦电容100N or 100uf 16V 10.只有10% 25V 的 11.在线放大器 Try to install a recent cvs image like boxman or ozoon in flash and then install a good image like nabilo or newnigma2 inusb or hdd. You will see that many problem will disappear That′s happen because you have a dm800 clone. Just find out what is the seconstage (69,70 or 72)it suports and put a patched image with the 第一步:将你的DM800hd的所有接口上的线拔掉，注意先拔掉电源线，再拔掉高频头的同轴电缆 。 第二步：从路由器接一根直连网线插入DM800hdRJ45口。 第三步: 将刷机线，一头插入电脑串口，一头插入DM800hd串口。 注意： 此台电脑与路由器也是相连的。 第四步: 运行dreamup软件。 设置正确的串口 Serial Port 设置Local IP（PC）： 填写你的电脑的 IP地址。select one 填写你的电脑的IP地址 设置Remote IP (BOx) :填写你的 DM800hd死机之前的IP地址 第五步：点击Connect 第六步：插入电源线 注意：这时候一定要注意等2分钟，否则刷机还将需要10几分钟。 一定要等2分钟。第七步：点 Flash，按照原来的刷机流程刷机即可。 特点：你会发现通过这种网线与串口线配合的串口刷机法，速度飞快，大约2分钟即可完成刷机。 拆机将卡取出，再用串刷，第一次启动时一定要装好卡。应该可以救的。。。。 Replace the secondstage boot loader. There is a bug with newer loaders on SIMs 2.0.1 Then install DE for clone (Google the image). Dm800 keeps rebooting or shutting down at startup Spent most of the day yesterday messing around with 5 dm800s, mainly to swap over rev J \ K tuners with the L3 tuner. What I noticed was that on some of the 800s i changed, the boxes would reboot soon after the boot screen. At first I thought the tuners were not sitting correctly, so I double checked and tried again and same problem. So i thought maybe could be a sim issue and tried 69\70\2.01, same problem. So then i thought could be image problem, tried gemini, dreamelite and PLI, same problem. By now Im thinking ok i got some faulty L3 tuners, So I pulled out my main 800 clone that I had put a L3 tuner in back in May and tested it and tried the tuners, they all boot and work fine. ( more about that at the end). I then went back tried the L3s in the b