金属箔应变信号调理电路设计试题.doc

金属箔应变信号调理电路设计 龚萍 （陕理工物理与电信工程学院（系）电子信息工程专业1103班级，陕西 汉中 723000) 指导老师：秦伟 [摘 要]本设计实现了对应变信号的放大，滤波处理。详细介绍了一种基于AD620和AD705仪表放大器构成的微弱信号调理电路设计方法，该电路主要由AD620设计的放大电路，RC无源滤波电路，50Hz带阻滤波器，及AD705调零电路组成。其放大电路，滤波电路设计完成后，用Multisim11.0软件进行仿真，调整了电路的主要参数，并对电路进行更改，调试，设计。该信号调理电路可以实现对传感器输出的信号进行124倍的放大，截止频率为1000Hz的RC低通滤波处理，最后经过50Hz带阻滤波器的滤波，使输出信号可以满足设计要求。 [关键词]AD620；AD705；放大；滤波  Design of strain signal conditioning circuit for metal foil Gong Ping (Grade03,Class11,Electronic Information Engineering,College of physical and telecommunication engineering,Shaanxi University of technology,HanZhong,723000,Shaanxi) Tutor:Qin Wei [Abstract]The design of amplification, filtering processing for the strain signal. Described in detail the weak signal conditioning circuit design method and the circuit design method which is based on a AD620 and AD705 instrumentation amplifier,and the circuit mainly by the AD620 was adopted to design the amplifying circuit, passive RC filter circuit, 50Hz band stop filter, and the AD705 tune zero circuit. After the amplifying circuit and the filter circuit are designed, use Multisim11.0 software to simulate, adjust the main parameters of the circuit, and change, debug, design the circuit. The signal conditioning circuit can realize the sensor output signal of 124 times of amplification, cut-off frequency of 1000Hz RC low-pass filter processing, finally 50Hz band stop filter filter, the output signal can meet the design requirements [Keywords]AD620;AD705;amplify;filtering 目录 引言 1 1 方案选择 2 1.1 方案一 2 1.1.1 电源电路 2 1.1.2 应变片电路方案 2 1.1.3 集成放大电路方案 2 1.1.4 无源滤波电路方案 2 1.1.4 设计总框图 3 1.2 方案二 3 1.2.1 电源电路 3 1.2.2 应变片电路 3 1.2.3 集成放大电路方案 3 1.2.4 滤波电路方案 3 1.2.5 总体设计框图 4 1.3 方案对比 4 2 芯片介绍 5 2.1 AD620芯片 5 2.1.1 AD620引脚图 5 2.1.2 AD620特性 5 2.1.3 AD620工作原理 5 2.2 AD705芯片 6 2.2.1 AD705引脚图 6 2.2.2 AD705特性 7 2.3 OP07芯片 7 3 Multisim11.0软件介绍 8 4 硬件电路设计 9 4.1 电源电路 9 4.2 应变片电路 9 4.3 AD620一级放大电路 9 4.4 RC无源低通滤波电路 11