某蒸压加气混凝砌块墙体粉刷施工工艺_secret.docVIP

*****派出所警务业务用房和森林消防专业扑救业务用房工程 墙 体 粉 刷 施 工 工 艺 ****建筑工程有限公司 2009年8月10日 墙体粉刷施工工艺 本工程为**森林公安派出所警务业务用房和森林消防专业扑救业务用房工程，框架结构，建筑五层，高度为17.25m，建筑面积为1789.89m2，砌体采用600×240×180及600×240×120蒸压加气砼砌块，为防止其粉刷层开裂或空鼓，在粉刷层上满设耐碱玻璃纤维网格布。 一、工艺流程： 内墙抹灰工艺流程： 基体表面处理 挂 吊直、套方、贴灰饼、设标筋 界面处理 做护角 抹底层灰 抹面层外墙抹灰工艺流程： 基体表面处理 挂 挂线、贴灰饼、设标筋 （界面处理）抹找平层 （抹防水层） 抹面层（保护层） ） 直线度 4 2 拉5m线，不足5m拉通线，用钢直尺检查 5 墙裙、勒脚上口直线度 4 2 拉5m线，不足5m拉通线，用钢直尺检查 四、注意事项： 1、墙体砌筑完毕，15天后进行顶砖施工；顶砖施工完毕，验收合格，7天后方可进行抹灰工程的施工。必须置于抹灰层内，严禁外露。抹灰砂浆在凝结前应防止暴晒、淋雨、水冲、撞击、振动；凝结后应及时进行湿润养护，普通水泥砂浆墙面宜养护7天，防水砂浆墙面宜养护14天。外墙严禁内外两侧同时进行抹灰，抹灰间隔时间不少于一天。抹灰砂浆中的打底砂浆，其强度等级不应低于砌块的强度等级。外墙抹灰之前，应对门窗框和砌体之间的缝隙进行处理；缝隙处理方法为：用纤维防水砂浆或聚合物防水砂浆填塞密实并用不小于1mm厚的聚合物水泥基防水涂膜涂刷一层，宽度不小于100mm。 manufacturers drawings bolt fastened in the cylinder and outer cylinder. Cylinder cylinder in the drain pipe installation and measuring component leads. 6.4.4.3 blade carrier, partitions and lower installation check the sealing ring of the seal and springs, which shall conform to the technical requirements manufacturers drawings. Cylinder gasket on the mounting brackets supporting the Group assembled, the lugs shall be no Burr on the surface, and other debris. Department suite in place to measure surface and inner cylinder surface height difference, compared with the original values confirm the location. 6.4.4.4 lower bearing and thrust bearing installation clean bearing and bearing, thrust bearing joints, clean them with a thin layer of turbine oil, and then lifting it to bits. 6.4.4.5 high and middle pressure cylinder over it to the end (for high pressure rotor and low pressure change flange gasket without connection unit) rotors and rotor flange gasket connection and there is no connection, so the rotor in place cases, rotors in place must be high and middle pressure cylinder together with the Chamber over it to the end. Jack in the box that are installed on a push-pull device of adjusting the high and medium pressure cylinder to