[模具教程] G10.0裙边分型面向四面光顺延伸技巧.docVIP

[模具教程]?UG10.0裙边分型面向四面光顺延伸技巧 ? 裙边分形型面向四面光顺延伸技巧$ U5 x8 O, s- w V; E7 P9 H ?5 g+ ?% [! C- U( c, O5 k) N, ?很多运动器材或玩具为了防止棱边对人体造成割伤，前后都包有R角，在这种情况下，为了保证模口角度接近直角，分型面最好做成法向面，即“裙边面”，如图：5 @5 Z n+ V }; Z a/ J0 m) f: Q! i$ T @; j u/ ~9 B, V z V$ i W裙边面和产品面成90度，但由于法向随分型线空间变化，通常很难延伸到模仁边缘，左右镜像排位时也很难接顺，在这里，我给大家分享一下我的解决方案$ h t6 z ?% o 先将裙边面宽度控制在8-10mm以内 利用管道求交 3 v2 k( l5 i+ R7 @( I# e# C# P7 D t1 Q, ^ 取一边水平拉伸，以侧角45度分段 0 m- r. s6 {7 A/ a/ { 再用管道修剪片体， # I8 s/ Y8 `, z6 g1 g 曲线组曲面对边接顺 S; R0 @??B1 n$ r m: X; C ?1 u+ y! _# a# }; S. f 同样的方法做出对面 再将另一侧边线两头缩短 % X+ u- h; c% m# r L7 x* j/ `2 Z n6 z% p- P% d4 z( h. Y4 f 桥接曲线接顺 $ ~7 K; R* E( { i) z# V j 再拉伸成曲面 2 d C2 M k5 m6 P S. M; i, [ 再用管道修剪 , Z ]+ w, W??X, x8 U 用曲线组曲面接顺 用同样方法做出对面 0 S3 I/ m/ V( [9 b | 用产品生成块，方块要在四个方向盖过桥接曲面 ??Q1 B6 s E5 b2 C$ {, n v 再求交 用此方法做的分型非常好排位，镜像不用接都是顺的，且延伸再长距离都无压力. ? ? 如有需要请加我QQ：2936668579 联系电话0769华陶静老师 加我QQ或找我电话可赠送UG下载视频教程 be limited to no more than 2 days of work, material deposited in special insulated containers, material handling to gently and make use of thermal insulation material in windproof, waterproof, moisture-proof measure. 6.2 thermal design optimization for high-temperature special thermal insulation for piping support and hanger design, reduced heat dissipation of the hangers, ensure that the wall does not overheat. Small-diameter piping, thermal instrument layout and positioning of support and hanger design take fully into account the expansion space and insulation thickness. Large-diameter pipes after heat preservation plastering construction of valves, turbine, checking smooth surface, high temperature powder paint fully dry after. Protective coverings for electric equipment insulation boards designed with pressure plate, when ordering according to the installation diagram, model specifications publishing order, ensure when installing corners neat, uniform appearance, reduce the amount of on-site machining. Before valves, flange