铸铜调节阀-VT铸铜调节阀.docVIP

铜阀门铜调节阀铸铜调节阀 产品名称： 铸铜调节阀 产品型号： VET 产品口径： DN25-50 产品压力： 0.6~10.0Mpa 产品材质： 铸钢、不锈钢、合金钢等 产品概括： 生产标准：国家标准GB、机械标准JB、化工标准HG、美标API、ANSI、德标DIN、日本JIS、JPI、英标BS生产。阀体材质：铜、铸铁、铸钢、碳钢、WCB、WC6、WC9、20#、25#、锻钢、A105、F11、F22、不锈钢、304、304L、316、316L、铬钼钢、低温钢、钛合金钢等。工作压力1.0Mpa-50.0Mpa。工作温度：-196-650℃。连接方式：内螺纹、外螺纹、法兰、焊接、对焊、承插焊、卡套、卡箍。驱动方式：手动、气动、液动、电动。 ? ? 产品详细信息 概述???? VET调节阀系列螺纹铸铜阀门配以电子驱动控制装置后，能调节蒸汽或冷、热水的流量，广泛用于中央空调、采暖、水处理、工业加工行业等系统流体控制。型号列表??外形尺寸??技术特点及规范??1、阀体：黄铜? 2、阀杆：不锈钢(1Cr18Ni9)? 3、阀杆密封件：丁青橡胶+聚四氟乙烯? 4、联接方式：G型内螺纹丝口? 5、公称压力：1.6Mpa? 6、介质：水/蒸气? 7、流体最大温度：常温（-10~120℃）? 8、泄漏量：≤0.03%/Kvs（在规定压差力）? 9、水流方向：按箭头方向（二通）? 10、阀门打开关闭方向：向上开、向下关（二通） appearance of the weld appearance quality technical requirements of the project must not have a molten metal stream does not melt the base metal to weld, weld seam and heat-affected zone surface must not have cracks, pores, defects such as crater and ash, surface smoothing, weld and base metal should be evenly smooth transition. Width 2-3 mm from the edge of weld Groove. Surface reinforcement should be less than or equal to 1 + 0.2 times the slope edge width, and should not be greater than 4 mm. Depth of undercut should be less than or equal to 0.5 mm, total length of the welds on both sides undercut not exceed 10% of the weld length, and long continuous should not be greater than 100 mm. Wrong side should be less than or at 0.2T, and should not be greater than 2 mm (wall thickness mm t) incomplete or not allow 7.5 7.5.1 installation quality process standards of the electrical enclosure Cabinet surface is clean, neat, no significant phenomenon of convex, close to nature, close the door. 7.5.2 Cabinet Cabinet face paints no paint, returned to rusted, consistent color. 7.5.3 uniform indirect gap from top to bottom, slot width 1.5mm 7.5.4 adjacent Cabinet surface roughness is 0. 7.5.5 the cabinets firmly fixed, crafts beautiful. 7.5.6 Cabinet surface gauge, switch cabinet mark clear, neat, firm paste. 7.5.7 Terminal row