胡汉才编著《理力学》课后习题答案第4章习题解答.docVIP

4－1.套管A由绕过定滑轮B的绳索牵引而沿铅垂导轨上升，滑轮中心到导轨的距离为l，如图所示。设绳索以等速拉下，忽略滑轮尺寸。求套管A的速度和加速度与距离x的关系式。 4－2.图示摇杆滑道机构中的滑块M同时在固定的圆弧槽BC和摇杆OA的滑道中滑动。如弧BC的半径为R，摇杆OA的轴O在弧BC的圆周上。摇杆绕O轴以等角速度转动，当运动开始时，摇杆在水平位置。试分别用直角坐标法和自然法给出点M的运动方程，并求其速度和加速度。 4－3.如图所示，光源A以等速v沿铅直线下降。桌子上有一高为h的立柱，它与上述铅直线的距离为b。试求该柱上端的影子M沿桌面移动的速度和加速度的大小（将它们表示为光源高度y的函数）。 4－4.小环M由作平动的丁字形杆ABC带动，沿着图示曲线轨道运动。设杆ABC的速度常数，曲线方程为。试求环M的速度和加速度的大小（写成杆的位移x的函数）。 4－4.如图所示，曲柄CB以等角速度绕C轴转动，其转动方程为。滑块B带动摇杆OA绕轴O转动。设，。求摇杆的转动方程。 4－5.图示机构中齿轮1紧固在杆AC上，AB=O1O2，齿轮1和半径为的齿轮2啮合，齿轮2可绕O2轴转动且和曲柄O2B没有联系。设，，试确定时，轮2的角速度和角加速度。 4－6.半径的圆盘绕其圆心转动，图示瞬时，点的速度为，点的切向加速度。试求角速度和角加速，并进一步写出点的加速度的矢量表达式。 4－7.圆盘以恒定的角速度绕垂直于盘面的中心轴转动，该轴在面内，倾斜角。点的矢径在图示瞬时为。求点的速度和加速度的矢量表达式，并用和检验所得结果是否正确。 a special tool to measure half a point the rotor shaft runout and simultaneous measurement of two coupling flutter testing, it should meet the requirements. Install the coupling housings to ensure embedded rotor coupling within a concave shoulder, and rotor clearance meets the design requirements. 6.4, 6, wearing construction technology of generator rotors demonstration 6.4.6.1 construction preparation and conditions through the stator before loading check and confirm to confirm air tightness test of the stator and stator mechanical, electrical, instrumentation and control and other related work had been completed. Internal cleaning of stator, high power vacuum the surface of the stator. Stator and rotor magnetic Center drainage is complete. In conjunction with the quality, mechanical, electrical and other relevant persons to finally cleaning check the stator, which is clean and free of any debris. Worn rotors check and confirm confirm before loading the rotor air tightness test, electrical test work has been completed. In conjunction with the quality, mechanical, electrical and other relevant persons to finally clean the rotors checked, its interior is clean and free of any debris. By quality, mechanical, electrical and other professionals to conduct an examinatio