支持match等,支持Gcode; DIY USB串口微型雕刻机.docVIP

支持match3等，支持Gcode; DIY USB/串口微型雕刻机 前言所谓的DIY就是do it yourself，你自己动手做，看到网上相当一部分人都是买来别人的现成的控制板，是别人做好的！！好了，我们也不可能从DIY一个芯片开始，太不现实了O(∩_∩)O~好了，言归正传；那么我为什么克服种种困难要DIY这个东西呢；首先：俺木有台式机电脑，所以并口也就无从谈起；淘宝上也有USB口的控制板二三百块吧，对俺这个不是天天使用雕刻机的人来说，几十块钱做一个更划算，用着心里踏实；浯危阂恍暇傻拇蛴』ㄉ厦娴牟浇缁突埽恿送上У模铱从美醋鲆桓鑫裼Ω每梢裕美醋昕祝龆魍妫???????USB/serial????atmega328/168PC-———------MCU——-----------L297+L298--step motors1:只能USB转串口线了。。。2：连接到主控芯片3 主控芯片电路板特写，呵呵洞洞板;公共GND下面两个是控制主轴的，我忘了标示了4：L297电路板 主控芯片连接的L297电路板5：L298 电路板 ，为什么L298和L297不焊到一个板子上呢？这样不更可靠吗？因为当初是直接用89S52控制L298，直接写代码控制的；所以用了L297后才发现，L297+L298让步进电机运动的好流畅，好平稳好欢快O(∩_∩)O~6 打印机 X轴7 淘宝上买的二手的日本的东东，非常好 Y轴还有怎么固定Z轴呢？？？？？？？开始时是自己做的控制板，如果仔细看下面的图片你会发现，有一个89S52芯片，对了，开始时，我是利用89S52通过串口读取PC的发来的数据，然后控制步进电机运动指定的位置；程序也实现了，功能也OK了，但是我发现89S52处理速度比较慢；而且经常卡着，不知道是不是因为和我褂肬SB转串口有关系；过了一段发现那个老外用激光DIY雕刻机那个，而且更为俺鸡冻的是他也是使用的串口的，更让我特别鸡冻的是，那个控制软件是开源的，而且支持标准GCODE，太好了，简直天助我也。 school)], 4 4 house building as well as more than 1000 copies of books, more than 10 kinds of collection of newspapers and magazines, fires burnt down. In 1938, the Japanese learned that the national Government established in XI Tang Tomb rotten clip taxes, tax officers live in 8 of Yan Dong village farmers home, troops at night, Yao was burned several houses. 1938 new morning of September 18, the Japanese team went to the countryside sweep from the kaiyang village line to Tung Yang Jia Qiao yan Temple wall and met Yang Jia溇 Zhou Dana (male) weeks because of long-term illness and cant work in the fields, the Japanese see his face from scratch without calluses, regard him as Shina, thrust a knife at the scene of his death. The body was stabbed 7 times, wound 13. The same day, Trang bang village heard the Japanese come to mop-up are hiding, mother of 9 Zhou Guanbao Zhang Aying to drill a dry mound, was discovered by the Japanese, a shot in the end. The same day, is 7 zhouhaijiangzhi grandfather Zhou Yingbao to escape the Japanese army, was found on the road, a shot in the end. In March 1939, the J