大亚湾聚泰花园高支模方案答案.doc

目　录 工程概况··················································3　　　　　　　　　　　　　　　　　　　　　　　　 编制依据··················································3 参数信息··················································3 模板面板计算··············································6 模板支撑方木的计算········································7 托梁材料计算··············································9 模板支架立杆荷载设计值（轴力）·····························10 立杆的稳定性计算·········································11 模板支架参数·············································13 梁侧模板荷载计算·········································14 十一、梁侧模板面板的计算······································15 十二、梁侧模板支撑的计算······································17 十三、穿梁螺栓的计算··········································21 十四、梁底模板计算············································21 十五、梁底支撑的计算··········································23 十六、梁跨度方向钢管的计算····································27 十七、扣件抗滑移的计算········································27 十八、立杆的稳定性计算········································27 十九、梁模板高支撑架的构造和施工要求（工程经验）···············29 二十、楼板强度的计算··········································29 二十一、梁和楼板模板高支撑架的构造和施工要求··················31 二十二、梁模板工程材料匡算·····································32 二十三、模板整体倒塌应急措施··································34 一、工程概况： 聚泰花园一期工程，位于惠州市大亚湾西区的龙山一路，占地面积约为2万平方米。一起建筑为6栋31~33层高层建筑，剪力墙结构，两层地下室，埋深约7.5米，局部为两层商业网点，框架剪力墙结构。工程重要性等级为一~三级，建筑基坑侧壁安全等级为二级。总建筑面积约14.7万㎡，由惠州大亚湾向荣实业有限公司投资建设，深圳奥意建筑工程设计有限公司设计，深圳合创建设工程顾问有限公司监理，广东省第二建筑工程公司组织施工； 本工程地下结构在顶层（+0.40m标高）处DR、DN轴交D1～D25轴间楼面支模高度达6.9m；D22～D25轴交DR～DA轴楼面支模高度达6.5m；梁高主梁为300*800，顶板厚180，柱为600*600。 二、编制依据： 高支撑架的计算依据《建筑施工扣件式钢管脚手架安全技术规范》（JGJ130-2011）、《混凝土结构设计规范》GB50010-2010、《建筑结构荷载规范》(GB 50009-2012)、《钢结构设计规范》(GB 50017-2003)等规范编制。 因本工程模板支架高度大于4.5米，根据有关文献建议，如果仅按规范计算，架体安全性仍不能得到完全保证。为此计算中还参考了《施工技术》2002（3）：《扣件式钢管模板高支撑架设计和使用安全》中的部分内容。 三、参数信息: 1.模板支架参数 横向间距或排距(m):1.00；纵距(m):1.00；步距(m):1.50； 立杆上端伸出至模板支撑点长度(m):0.10；模板支架搭设高度(m):6.90； 采用的钢管(mm):Φ48×3.5 ；板底支撑连接方式:方木支撑； 立杆承重连接方式:可调托座； 2.荷载参数 模板与木板自重(kN/m2):0.350；混凝土与钢筋自重(kN/m3):25.