Cast iron ipe outer surface layer of paint should be complete is bright and clean.docVIP

下载本文档

5
0
约1.16万字
约 6页
2016-11-29 发布于贵州
举报
版权申诉

Cast iron ipe outer surface layer of paint should be complete is bright and clean.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

Cast iron ipe outer surface layer of paint should be complete is bright and clean

Cast iron pipe outer surface layer of paint should be complete is bright and clean, attached firmly. 4) the size of the cast iron pipe, pipe fittings deviation should be allowed to meet the requirements 5) flange to the center line of pipe or tube should be vertical, both ends flanges shall be parallel. Flange surface convex sets and the sealing groove. Cast iron pipe fittings, such as hydraulic pressure test data without factory, before use must 10% per batch smoke a water pressure test, pressure test should be according to standard metallurgical enterprise in the continuous cast iron straight pipe and pipe fittings (YB 427-64), the cast iron straight pipe and pipe fittings (YB 427-64). If there are unqualified, should be checked by the root. (2) acceptance of concrete and reinforced concrete 1) tube inside and outside surface should be bright and clean level off, the honeycomb, slump, no, empty drum. 2) crack is not permitted in concrete pipe; Reinforced concrete pipe outside surface crack is not permitted, tube wall crack width must not exceed 0.05 mm. Crack and the dry shrinkage of the mortar layer on the surface of the crack. 3) the commissure should not leak slurry. 4) in any of the following circumstance of tube, and allowed to repair: 1) slump area of not less than 1/20 of the surface area of the tube, did not reveal hoop reinforcement. (2) surface area concave depth was less than 5 mm; Sticky skin depth is less than 1/5 of the wall thickness, the maximum of no more than 10 mm; Sticky skin, the area of voids, pits no more than 1/20 of the surface area, each area is less than 100 cm2. (3) joint leak slurry depth of no more than 1/3 of the wall thickness, length of no more than 1/3 of the length. (3) the acceptance of the new plastic pipe The appearance quality of the pipes, pipe fittings shall meet the following requirements: 1) color should be uniform, without decomposition and uneven color on the color line; 2) inner surface smooth, level off