《传动盖冲压工艺制定及冲孔模具设计说明书》.docVIP

摘 要 本设计中介绍了传动盖冲孔的冲压工艺分析，工艺方案的分析和制定，排样图的设计，总的冲压力计算及压力中心的计算，刃口尺寸的计算，弹簧的计算和选用，凸模、凹模或凸凹模结构设计以及其他冲模零件的结构设计，绘制模具装配图和工作零件图，编写设计说明书，填写冲压工艺卡和工作零件机械加工工艺过程卡，注意凸、凹模的配合加工。有关工艺参数的计算，如：冲裁力、卸料力的计算。冲孔模具结构设计中有关于非标准件的计算与设计等等。 关键词：凸模； 凹模；工艺;装配图 Abstract In this design introduced the transmission covers the punch holes the ramming craft analysis, the craft plan formulation, arranges the specimen map design, the always ramming strength computation and the center of pressure computation, the cutting edge size computation, the spring, the rubber computation and selects, the raised mold, the concave mold or the convex-concave mold structural design and all that die the components structural design, draws up the mold assembly drawing and the work detail drawing, the compilation design instruction booklet, fills in the ramming craft card and the work components machine-finishing technological process card, raised pays attention to, the concave mold coordinate processing. The calculation concerning craft parameter, such as: Hurtle to cut the dint and unload the calculation of anticipate the dint. The blunt bore molding tool structure designs the medium calculation and the design etc. concerning not standard piece. Key words: Raised mold; Concave mold; Plan; Installation; 目录 TOC \o 1-2 \h \z HYPERLINK \l _Toc256000000 锇飚琨骸犀邮镥繁陉式 PAGEREF _Toc256000000 \h 2 HYPERLINK \l _Toc256000001 1、绪论耋尴哗壶垢檫庹渍殁喱 PAGEREF _Toc256000001 \h 0 HYPERLINK \l _Toc256000002 2、 工艺编制狻棘缯歧踌栖撺绳奶验 PAGEREF _Toc256000002 \h 2 HYPERLINK \l _Toc256000003 2.1工艺分析甥襁遢娩埽激砂睢轸茄 PAGEREF _Toc256000003 \h 2 HYPERLINK \l _Toc256000004 2.2 工艺方案的分析和确定瑁鹨邓壬府凉踣戳界泮 PAGEREF _Toc256000004 \h 2 HYPERLINK \l _Toc256000005 2.3 确定各工序模具种类及型式绎鞍佗锊努妒鎏纲鞒齿 PAGEREF _Toc256000005 \h 3 HYPERLINK \l _Toc256000006 2.4 主要工艺参数计算逞阂?匈丝融倏屋脆铷 PAGEREF _Toc256000006 \h 3 HYPERLINK \l _Toc256000007 2.5 计算各工序压力、压力中心、初选压力机 耀嘎馁邻蠡笞沌哦烫级 PAGEREF _Toc256000007 \h 4 HYPERLINK \l _Toc256000008 2.6 确定冲压设备醯眸瞀狱但饲涧镏负襞 PAGEREF _Toc256000008 \h 4 HYPERLINK \l