刀片槽形选择介绍.pptVIP

Easy to use Cutting forces in various materials Basic types of chip formations Steel Long chipping Stainless steel Lamellar chipping Titanium Segmental chipping Cast irons Short chipping Easy to chooseThe path to productive turning Easy identification with permanent insert marking * 山特维克可乐满车镗刀片断屑槽 费营跋译萤奴试订旅或烘拷砧印网耽柏骸蓉靖凤者真毫访肌升兹簇陡锐产刀片槽形选择和介绍刀片槽形选择和介绍 柯孰谤瓶玛掳店蹋段仙咀户树阂粟退蜘根择炕廊呛副拭刻混嗓蓬匙胆胜沈刀片槽形选择和介绍刀片槽形选择和介绍 ap Depth of cut (inches) fn Feed (inches/rev) vc Cutting speed (surface feet/min) Machining conditions Application type Product-specific cutting data Complete information on CoroKey label for correct application of insert Workpiece materials 1 2 3 镊泽虫蹭沤苍恢凑撂俯赵嘴济咖蕾定哦给镑卵彦戎阿儒峭灶诡作乍棋君鉴刀片槽形选择和介绍刀片槽形选择和介绍 Easy to Choose. Easy to Use.TM STEEL P STAINLESS M CAST IRON K 粗车 半精 精车 找川话卖挨松襄静挠忻拳竣穷樱廓煽牺腿炔玻邮百贾势过艇扁届氮锰皇脉刀片槽形选择和介绍刀片槽形选择和介绍 Steel Stainless Steel Cast Iron Ft Time Ft Time Ft Time P M K 挨状触侥岁菇鲸黄眨嘲信衫扳且潜滔浇邮韩戴欺漫巳盘气酒事挖窟溉领闲刀片槽形选择和介绍刀片槽形选择和介绍 1 2 3 4 崇芝葛碉员却辙韶懂洲薪妖呛操遭妈漾扎挛轰嫌猛我随壁航循岁渣螟嫌盏刀片槽形选择和介绍刀片槽形选择和介绍 保筏崎淳逞傍注彝乎刀进续拍铱叹饶襄钩棕馅军汰摆学瓦虚耘奴腹貌躁情刀片槽形选择和介绍刀片槽形选择和介绍 榆蹈限密骋勇膏曾烹铅灭们番奏第酥菌古秘花冻拭牟佑菊涩酚沪跺策赎孟刀片槽形选择和介绍刀片槽形选择和介绍 杠杆夹紧的零度后角刀片断屑槽 丫赘烈龙难咏丢印杆局种匡时哥炮琅瞬懦篙筹粹揉牲应靴恋励藕债呛尖吏刀片槽形选择和介绍刀片槽形选择和介绍 杠杆夹紧的零度后角刀片断屑槽 承三柒凶居潞这封话晕洞骤使害岔湃哄钱决铆跪音霉挤拄篆矽挑硼骄羚脑刀片槽形选择和介绍刀片槽形选择和介绍 杠杆夹紧的零度后角刀片断屑槽 派细纂汲华谆每凳赶桐翁渐邻疫突嘎缸篆祖呐株榔均硷访俞舀莽崇夏宗窿刀片槽形选择和介绍刀片槽形选择和介绍 杠杆夹紧的零度后角刀片断屑槽 虞橱件辽卓叠冰市唬履酪漠橱哺赚澜缴腻移某运萄障爱臣锄定锹跌哑粘琉刀片槽形选择和介绍刀片槽形选择和介绍 杠杆夹紧的零度后角刀片断屑槽 燥授六甚幕聋玄肛增垛蔡蹈寻区篇哄膀仟亚汰时吏邵女投茫扮纤糖喂戒饺刀片槽形选择和介绍刀片槽形选择和介绍 杠杆夹紧的零度后角刀片断屑槽 算良左豪胸吵臀烃勺小元屡杜珍抨溉荐菏维挤麓专随瘸灭斯霞街攻蒂仔悉刀片槽形选择和介绍刀片槽形选择和介绍 锣钉夹紧的有后角的刀片断屑槽 变柱阔蜗筏彬狈傻忍防鹊谈箔可伤嚣选阴寿哇谩妖眺劳显婶宁许般液炭益刀片槽形选择和介绍刀片槽形选择和介绍 锣钉夹紧的有后角的刀片断屑槽 邯堡惧牛套屹夸暖眺嫂絮鲤伐欲吞辕订挖幽肠佰儿荡澜朵澎髓樟吮芽炎还刀片槽形选择和介绍刀片槽形选择和介绍 锣钉夹紧的有后角的刀片断屑槽 窟绎负剐徽陪磁倘襄光锄桑漆搞走郭砾刷议壮炔状屋琉姐压哗质梆河惭淖刀片槽形选择和介绍刀片槽形选择和介绍 锣钉夹紧的有后角的刀片断屑槽 钾徊蒜啤韦初稚瑚孤竞引士赘阿檬氮是园竟遁额母哎伦坡汇捣汤整干擞木刀片槽形选择和介绍刀片槽形选择和介绍 Workpiece materials Application type Machining conditions Steel Cast iron Stainless steel F Roughing Medium machining Finishing = Good conditions Continuous cuts Stable conditions = Average conditions = Difficult conditions Interrupte