多点温度采集原理图与C语言程序.docVIP

主要程序，已经实验通过 #includereg52.h #define uchar unsigned char #define uint unsigned int sbit DQ=P3^7; sbit D1=P2^3; sbit D2=P2^2; sbit D3=P2^1; sbit D4=P2^0; sbit key1=P3^3; sbit key2=P3^4; sbit key3=P3^5; uchar code tab[]={0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90,0x40,0x79,0x24,0x30,0x19,0x12,0x02,0x78,0x00,0x10}; uchar code tabnum1[]={0x28,0x5B,0x2E,0xC7,0x02,0x00,0x00,0x62}; uchar code tabnum2[]={0x28,0x38,0x0E,0x3B,0x02,0x00,0x00,0x63}; uchar code tabnum3[]={0x28,0x39,0xF5,0x3A,0x02,0x00,0x00,0x0D}; uint tvalue;//温度值 uchar tflag,flagdat,t,hh1;//温度正负标志 uchar tt,kk,dd; void delay(uint z) { uint x,y; for(x=z;x0;x--) for(y=110;y0;y--); } void delay_18B20(unsigned int i)//延时1微秒 { while(i--); } void ds1820rst()//ds1820复位* { unsigned char x=0; DQ = 1; //DQ复位 delay_18B20(4); //延时 DQ = 0; //DQ拉低 delay_18B20(100); //精确延时大于480us DQ = 1; //拉高 delay_18B20(40); } unsigned char ds1820rd()//读数据 { unsigned char i=0; unsigned char dat = 0; for (i=8;i0;i--) { DQ = 0; //给脉冲信号 dat=1; DQ = 1; //给脉冲信号 if(DQ) dat|=0x80; delay_18B20(10); } return(dat); } void ds1820wr(uchar wdata)//写数据 {unsigned char i=0; for (i=8; i0; i--) { DQ = 0; DQ = wdata0x01; delay_18B20(10); DQ = 1; wdata=1; } } void changds18b20_1(uchar a[8]) //往18B20写序列号 { ds1820rst(); delay(1); ds1820wr(0x55); //285B 2E C7 02 00 00 62 delay(1); ds1820wr(a[0]); ds1820wr(a[1]); ds1820wr(a[2]); ds1820wr(a[3]); ds1820wr(a[4]); ds1820wr(a[5]); ds1820wr(a[6]); ds1820wr(a[7]); } read_temp1()//读取温度值并转换 {uchar a,b; ds1820rst(); changds18b20_1(tabnum1); //写序列号 ds1820wr(0x44);//启动温度转换 ds1820rst(); changds18b20_1(tabnum1); ds1820wr(0xbe);//读取温度 a=ds1820rd(); b=ds1820rd(); tvalue=b; tvalue=8; tvalue=tvalue|a; if(tvalue0x0fff) tflag=0; else {tvalue=~tvalue+1; tflag=1; } tvalue=tvalue*(0.625);//温度值扩大10倍，精确到1位小数 return(tvalue); } read_temp2()//读取温度值并转换 {ucha