MSR系列路由IPv6的PIM-SM典型配置.docVIP

MSR系列路由器 IPv6的Pim-SM的典型配置 关键词：MSR; IPv6 PIM-SM;MLD;组播; 一、 RTA的端口E0/1连接组播源，端口S0/1连接RTB，端口S0/2连接RTC分别在端口上启IPv6 PIM-SM组播协议；RTB的端口S0/2连接RTA，端口S0/1连接RTC，端口E0/1连接接受主机Receiver2，分别在端口上启IPv6 PIM-SM组播协议,连接接受主机端口起MLD协议；RTC的端口S0/1连接RTA，端口S0/2连接RTB，端口E0/1连接接受主机Receiver1，分别在端口上启IPv6 PIM-SM组播协议,连接接受主机端口起MLD协议。 设备清单：MSR系列路由器3台 二、组网图： 三、配置步骤： RTA关键配置脚本 # //全局使能IPv6 ipv6 # //启动IPv6的ospfv3 路由协议 ospfv3 1 router-id 1.1.1.1 # //全局启动IPv6组播协议 multicast ipv6 routing-enable # //连接IPv6组播源的地址 interface Ethernet0/1 port link-mode route ipv6 address 6::1/64 undo ipv6 nd ra halt ospfv3 1 area 0.0.0.0 pim ipv6 sm # //连接RTB的接口地址 interface Serial0/1 link-protocol ppp ipv6 address 1::1/64 ospfv3 1 area 0.0.0.0 pim ipv6 sm # //连接RTC的接口地址 interface Serial0/2 link-protocol ppp ipv6 address 2::1/64 ospfv3 1 area 0.0.0.0 pim ipv6 sm # RTB关键配置脚本 # //全局使能IPv6 ipv6 # //启动IPv6的ospfv3 路由协议 ospfv3 1 router-id 2.2.2.2 # //全局启动IPv6组播协议 multicast ipv6 routing-enable # //连接RTA的接口地址 interface Serial0/2 link-protocol ppp ipv6 address 1::2/64 ospfv3 1 area 0.0.0.0 pim ipv6 sm # //连接IPv6组播接收Receiver2 interface Ethernet0/1 port link-mode route ipv6 address 5::1/64 undo ipv6 nd ra halt ospfv3 1 area 0.0.0.0 mld enable mld version 2 pim ipv6 sm # //连接RTC的接口地址 interface Serial0/1 link-protocol ppp ipv6 address 3::1/64 ospfv3 1 area 0.0.0.0 pim ipv6 sm # RTC关键配置脚本 # //全局使能IPv6 ipv6 # //启动IPv6的ospfv3 路由协议 ospfv3 1 router-id 3.3.3.3 # //全局启动IPv6组播协议 multicast ipv6 routing-enable # //配置ACL acl ipv6 number 2000 rule permit source ff0e::1 64 //连接RTA的接口地址 interface Serial0/1 link-protocol ppp ipv6 address 2::2/64 ospfv3 1 area 0.0.0.0 pim ipv6 sm # //连接IPv6组播接收Receiver1 interface Ethernet0/1 port link-mode route ipv6 address 4::1/64 undo ipv6 nd ra halt ospfv3 1 area 0.0.0.0 mld enable mld version 2 pim ipv6 sm # //连接RTB的接口地址 interface Serial0/2 link-protocol ppp ipv6 address 3::2/64 ospfv3 1 area 0.0.0.0 pim ipv6 sm # //配置C-BSR与C-RP pim ipv6 c-bsr 3::2 c-rp 3::2 group-pol