塑模设计中常见术语的英文翻译.docVIP

塑模设计中常见术语的英文翻译 塑料成型模具：mould for plastics 热塑性塑料模：mould for thermoplastics 热固性塑料模：mould for thermosets 压缩模：compression mould 压注模：transfer mould 注射模：injection mould 热塑性塑料注射模：injection mould for thermoplastics 热固性塑料注射模：injection mould for thermosets 溢料压缩模：flash mould 半溢料压缩模：semi-positive mould 不溢料压缩模：positive mould 移动式压缩模：portable compression mould 移动式压注模：portable transfer mould 固定式压缩模：fixed compression mould 固定式压注模：fixed transfer mould 无流道模：runnerless mould 热流道模：hot runner mould 绝热流道模：insulated runner mould 温流道模：warm runner mould 浇注系统：feed system 主流道：sprue 分流道：runner 浇口：gate 直接浇口：direct gate 环型浇口：ring gate 盘型浇口：disk gate 轮辐浇口：spoke.gate 点浇口：pin-point.gate 侧浇口：edge.gate 潜伏浇口：submarine gate 扇形浇口：fan gate 护耳浇口：tab gate 冷料穴：cold-slug well 浇口套：sprue bush 浇口镶块：gating insert 分流锥：spreader 流道板：runner plate 热流道板：manifold block 温流道板：warm runner plate 二级喷嘴：secondary nozzle 热管；heat pipe 阀式浇口：valve gate 加料腔：loading chamber 柱塞：force plunger 溢料槽：flash groove 排气槽：vent 分型面:parting line 定模：stationary mould 动模：movable mould 上模：upper mould 下模：lower mould 型腔：cavity 凹模：impression 镶件：mold insert 活动镶件：movable insert 拼块：splits 凹模拼块：cavity splits 型芯拼块：core splits 型芯：core 侧型芯：side core 螺纹型芯：thread core 螺纹型环：thread ring 凸模：punch 嵌件：insert 定模座板：fixed clamp plate 动模座板：moving clamp plate 上模座板：upper clamp plate 下模座板：lower clamp plate 凹模固定板：cavity-retainer plate 型芯固定板：core- retainer plate 凸模固定板：punch- retainer plate 模套：chase 支承板：backing plate 垫块：spacer 支架：ejector housing 支承柱：support pillar 模板：mould plate 斜销：angle pin 滑块：slide 侧型芯滑块:side core-slide 滑块导板：slideguide strip 楔紧块；heel block 斜槽导板：finger guide plate 弯销：dog-leg cam 斜滑块：angled-lift splits 导柱：guide pillar 带头导柱：guide pillar straight 带肩导柱：guide pillar,shouldered 推板导柱：ejector guide pillar 导套：guide bush 直导套：guide bush,straight 带头导套：guide bush,head 推板导套：ejector guide bush 定位圈：locating ring 锥形定位件：mould bases locating elements 复位杆：ejector plate return pin 限位钉：stop pin 限位块：stop block 定距拉杆：length bolt 定距拉板：puller plate 推杆：ejector pin 圆柱头推杆：e