《模具结构.pptVIP

* * ④　重式浇口 重式浇口又称搭接浇口，它基本上与侧浇口相同，但浇口不是在型腔（塑件）的侧边，而是在型腔（塑件）的一个侧面。它是典型的冲击型浇口，可有效防止塑料熔体的喷射流动。如成型条件不当，会在浇口产生表面缩水，切除浇口比较困难，会在塑件表面留下明显的浇口痕迹。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. * * ⑤　扇形浇口 扇形浇口是逐渐展开的浇口，常用来成型宽度较大的板状塑件；塑料熔体在宽度方向得到均匀分配，可降低塑件内应力，减少其翘曲变形；型腔排气良好，避免包围空气，但是浇口切除比较困难，痕迹明显。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. * * ⑦　盘形浇口 盘形浇口又称薄板浇口或内圆环形浇口，盘形浇口用于内孔较大的圆筒形塑件，或具有较大正方形内孔的塑件。塑料熔体以相同压力均匀从内孔周边上进胶，空气顺利排除，这种浇口有较理想的充模状态，但塑料损耗量较大，且浇口切除困难。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. * * ⑧　圆环形浇口 圆环形浇口设置在与圆筒型腔同心的外侧，即在型腔四周设置浇口，其浇口位置正好与内侧盘形浇口相对应，它适用于薄壁长管形塑件。由于塑料熔体环绕型芯均匀地进入型腔，充模均匀，排气效果好，塑件无熔接痕。但浇口除去困难，并在塑件内侧留下明显的浇口痕迹。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. * * ⑩　附耳式浇口 附耳式浇口又称分接式浇口或调整式浇口，它在型腔侧面开设耳槽，塑料熔体通过浇口冲击在耳槽侧面上，经调整方向和速度后再进入型腔，因此可以防止小浇口直接对型腔注料时产生的喷射现象，它可减少浇口附近的内应力，防止型腔压力过大，对于流动性差的塑料有效,这种浇口除去比较困难，痕迹大。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. * * 未造平衡的分流道 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET