l提花纬编圆机产品设计.pptVIP

第三章 提花纬编圆机产品设计 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 知识点 理解纬编提花圆机的选针原理 了解此种机器所生产的产品种类 掌握纬编提花产品设计方法和上机工艺 重点掌握单、双面典型产品设计和上机 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 第一节提花轮选针原理与上机工艺 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 一、选针机构及选针原理 （一）选针机构 织针 起针三角 压针三角 提花轮 提花轮以20－40°倾斜角安装 提花轮钢片间距＝针距 提花轮钢片凹槽中可装高、低钢米或不装钢米 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 提花轮槽中装高钢米——织针上升至退圈高度——成圈 提花轮槽中装低钢米——织针上升至集圈高度——集圈 提花轮槽中无钢米——织针不编织 （二）选针原理 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 提花轮与针筒针数之间的关系 提花轮槽数=T 针筒总针数=N N = Z T+r Ｚ－正整数 r－余针数 有两种情况 总针数N可被提花轮槽数T整除(r =0 ) 总针数N不能被提花轮槽数T整除(r≠0 ) 二、矩形花纹的形成和设计 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. (一）总针数N可被提花轮槽数T整除(r =0 ) R=0时，N=Z T 针筒转一圈，提花轮转Ｚ转 花纹的最大宽度：Ｂmax＝Ｔ 花纹的最大高度：Ｈmax＝M/e Ｍ－机器路数（即提花轮个数） e －色纱数 (编织一横列所需路数) Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 例：N=12,T=4,M=4,e＝1 Bmax=T=4 Hmax=M/e＝4 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 例： 在提花轮提花圆机上编织2色提花织物（e=2），总针数 N=1500， 提花轮槽数T=15 ，机器路数 M=36 （1）计算 N/T=100 r=0 Bmax=T=15 （纵行） 取B=15纵行 Hmax =M/e =36/2=18（横列） 取H=18横列 机器1转可织一个完全组织高度 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. （2）设计花纹图案 B=15纵行 H=18横列 E