- 1、本文档共10页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
- 5、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
- 6、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们。
- 7、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 8、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
特斯拉無叶涡轮泵制作方法
特斯拉无叶涡轮泵制作方法
Building a Tesla Turbine from hard drive platters
Please note that I am not a Physicist or a machinist (yet). I have been interested in Nikola Tesla for some time, and I was looking for a project to gain some experience in the machine shop. My job is to provide Lecture Demonstrations, so my goal was to produce a teaching tool rather than an efficient engine.
For background material, Wikipedia has several good review articles about Nikola Tesla, the Tesla Turbine, the Boundary Layer Effect, and Reynolds Number.
Disks
At first I tried using CDs because of their large surface areas, but they didnt hold up too well under the milling machine. I also had a stack of platters from old and defective hard drives, but I didnt know if the smaller diameter disks would work as well.
One problem I ran into is that some newer hard drives use ceramic disks instead of metal. Theyre still coated with metal, but theyre thinner and a couple platters shattered when I tried to machine them:
My original plan for the center hole pattern had small holes (for threaded rods and washers for spacers), as well as large holes (for air vents).
The second set of platters had radial arcs cut in them such that the inside edge of the radial cutout is close to the outside diameter of the spacers that I removed from the hard drive assemblies.
The hard drive platters were stacked and clamped to a rotary table between two sheets of scrap aluminium but the top disk (above picture) still took some extra damage. The rest of the platters look much better though (see the complete rotor assembly below).
Spacers
I decided to be lazy and use the spacers that were between the platters in the original hard drive assemblies rather than machine my own. This increased distance (roughly .05 instead of .012) may lead to turblent flow rather than laminar flow but will be close enough for this project.
Shaft
With the turbine platters and spacers complete, I turned a shaft from round
您可能关注的文档
最近下载
- 公司章程英文版 Company Articles of Association.doc VIP
- 英文版公司章程ARTICLES OF ASSOCIATION OF.docx VIP
- 从《倾城之恋》的白流苏透析张爱玲小说中的女性形象.docx
- 档案搬迁服务 投标方案.doc
- 日本 东要介--透析液纯净化.cn.pdf VIP
- mpr300电机保护器使用使用说明书.doc
- 2025年乡村振兴战略下县域经济产业链优化研究报告.docx VIP
- 胜利仪器VICTOR 240.240S.270.270S双通道系列示波器用户手册.pdf VIP
- 智能浇灌系统的策划书3篇.pdf VIP
- 新HSK3级词汇最新分析和总结.pdf VIP
文档评论(0)