单片机各种初始化程序[精选].docVIP

#includeZLG7289.h unsigned long num=0; unsigned char Key_num=0; //键值 unsigned char mode=0; //模式 unsigned int key=0xff; unsigned int num1=0;//设定电压十位、个位和小数位 unsigned int num2=6; unsigned int num3=0; unsigned int num4=0;//输出电压十位、个位和小数位 unsigned int num5=0; unsigned int num6=0; unsigned int num7=0; unsigned int num8=0;//输出电流百位、十位和个位 unsigned int num9=0; unsigned int num10=0; unsigned int key_flag=0; double sum=0; unsigned int sam_v=0; //扩单10倍输出电压 unsigned int sam_c=0; //以mA为单位的电流 unsigned int a=0; unsigned int b=0; unsigned int c=0;// 计算转换采样值后得到的输出电压 sfr16 DAC0=0xD2; sfr16 ADC0=0XBE ; #define ref 2.434 void DelayMs(unsigned int i) //延时MS { unsigned int j; for(;i0;i--) for(j=1000;j0;j--) ; } void SystemInit() //看门狗配置 { //禁止看门狗 EA=0; WDTCN=0xDE; WDTCN=0xAD; EA=1; } void SYSCLK_Init() { int i; OSCXCN=0X77 ; //配置系统时钟为12Mhz for(i=0;i256;i++); while (!(OSCXCN0x80));//外部晶振起振且运行稳定 OSCICN=0x88; } void PORT_Init() { XBR0=0x04; //交叉开关不分配其他设备 XBR1=0x00; XBR2=0x40; //使能交叉开关 } void InterruptInit() //中断7初始化 { EIE2=0x20; //外部中断7中断允许 P3IF = 0x00; //下降沿触发，软件清零 EA=1; //中断总开关 } void T0_A/Dgengxin_1ms_init(void) //T0初始化 { CKCON=0xf7; // T0M=0，12分频 TMOD=0x10; //T0方式一16位定时/计数器 TH0=(65536-1000)/256; TL0=(65536-1000)%256; //定义初值 } void T1_ZLGxianshi_500ms_init(void) //T1初始化 { CKCON=0xef; //T1M=0，12分频 TMOD=0x01; //T1方式一 TH1=(65536-50000)/256; TL1=(65536-50000)%256; //定义初值 } void Timer0_ISR(void) interrupt 1 //T0溢出进入中断服务程序 { TH0=(65536-1000)/256; TL0=(65536-1000)%256; } void timer1interrupt() interrupt 3 //定时器1中断 { unsigned long total=0; //循环变量 TH1=65536-50000/256; //计数器重装 TL1=65536-50000%256; total++; while(total==10) //循环10次计时500ms { total = 0; } } void XIANSHI_Init() { ZLG7289_Download(1,0,0,0);//数码管初始化 ZLG7289_Download(1,1,0,0); ZLG7289_Download(1,2,1,0); ZLG7289_Download(1,5,0,0); ZLG7289_Download(1,6,0,0); ZLG7289_Download(1,7,0,0);ZLG7289_Hide(0xe7);// 3,4数