第6章 加工中心编程幻灯片.pptVIP

加工部位分析： 工步设计： 锪φ16mm孔进给路线: 钻螺纹底孔、攻螺纹进给路线: O0010 G21; G00 G90 G17 G40 G49 G80; G91 G28 X0 Y0 Z0 T01 M06; G00 G90 G54 X-215 Y0; M03 S300; Z100 G43 H01; Z-3.5; M98 P0001;/B面初铣 G91 G28 X0 Y0 Z0 T13 M06; G90 G00 Z100 G43 H13; Z-4; M03 S350; M98 P0001;/B面精铣 G91 G28 X0 Y0 Z0 T02 M06; G00 G90 Z100 G43 H02; M03 S400; M08; G98 G85 X0 Y0 Z-20 R5 F60;/初镗∮60孔 G80 M05; G49 M09; G91 G28 X0 Y0 Z0 T03 M06; G00 G90 Z100 G43 H03; M03 S450; M08; G98 G85 X0 Y0 Z-20 R5 F50;/半精镗∮60孔 G80 M05; G49 M09; 主程序 盖板零件的加工程序 G91 G28 X0 Y0 Z0 T04 M06; G00 G90 Z100 G43 H04; M03 S500; M08; G98 G76 X0 Y0 Z-20 R5 Q5 P2000 F40;/精镗 G80 M05; G49 M09; G91 G28 X0 Y0 Z0 T05 M06; G00 G90 Z100 G43 H05; M03 S1000; M08; G81 G99 X-50 Y0 Z-5 R3 F50；/钻8个中心孔 X-56.57 Y56.57; X0 Y50; X56.57 Y56.57; X50 Y0; X56.57 Y-56.57; X0 Y-50; G98 X-56.57 Y-56.57;/返回初始平面 G80 M05; G49 M09; G91 G28 X0 Y0 Z0 T06 M06; G00 G90 Z100 G43 H06; S600 M03; M08; G99 G81 X-56.57 Y56.57 Z-23 R5 F60;/钻4-∮10孔 X56.57; Y-56.57; G98 X-56.57; M09; G49 M05; G91 G28 Z0 T07 M06; G00 G90 Z100 G43 H07; M03 S300; G99 G81 X-56.57 Y56.57 Z-23 R3 F40;/扩孔4-∮11.85 X56.57; Y-56.57; G98 X-56.57; G80 M05; G49 M09; G91 G28 X0 Y0 Z0 T08 M06; G00 Z100 G43 H08; M03 S100; M08; G81 G99 X-56.57 Y56.57 Z-23 R3 F40;/铰孔至∮12H8 X56.57; Y-56.57; G98 X-56.57; G80 M05; G49 M09; G91 G28 X0 Y0 Z0 T09 M06; G00 Z100 G43 H09; M03 S150; M08; G81 G99 X-56.57 Y56.57 Z-5 R3 F30;/锪孔至∮16 X56.57; Y-56.57; G98 X-56.57; G80 M05; G49 M09; G91 G28 X0 Y0 Z0 T10 M06; G00 G90 Z100 G43 H10; M03 S450; M08; G81 G99 X-50 Y0 Z-23 R3 F60;/钻螺纹底孔 X0 Y50; Y0 X50; G98 X0 Y-50; G80 M05; G49 M09; G91 G28 X0 Y0 Z0 T12 M06; G00 G90 Z100 G43 H12; M03 S100; G84 G99 X-50 Y0 Z-19 R5 F200;/攻螺纹4-M16 X0 Y50; X50 Y0; G98 X0 Y-50; G80 M09; G49; M05; M30; G00 X-135 Y45; M08; G01 X75 F70; Y-45; X-135; G00 X-215 Y0; G00 G49 Z100; M09; M05; M99; O0001 Ⅱ．SIEMENS 802D数控系统编程 SIEMENS 802D数控铣系统指令 1、平面选择指令G17-G19 2、绝对值和增量值指令G90, G91, AC, IC 在位置数据不同于G90/G91的设定时，可在程序段中通过AC/IC以绝对尺寸/相对尺寸方式进行设定。 如：X=AC_; 表示X轴以绝对坐标输入