[第3单元]虚拟机技术及应用.pptVIP

  • 14
  • 0
  • 约2.55万字
  • 约 86页
  • 2017-02-12 发布于湖北
  • 举报
[第3单元]虚拟机技术及应用

* * * * * * * * * * * * * * * * * * * * * * * * * * * ? 2007 Microsoft Corporation. All rights reserved. * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * ? 2007 Microsoft Corporation. All rights reserved. * * ? 2007 Microsoft Corporation. All rights reserved. * * ? 2007 Microsoft Corporation. All rights reserved. * * ? 2007 Microsoft Corporation. All rights reserved. * * ? 2007 Microsoft Corporation. All rights reserved. * * ? 2007 Microsoft Corporation. All rights reserved. * * ? 2007 Microsoft Corporation. All rights reserved. * * ? 2007 Microsoft Corporation. All rights reserved. * * ? 2007 Microsoft Corporation. All rights reserved. * * ? 2007 Microsoft Corporation. All rights reserved. * * ? 2007 Microsoft Corporation. All rights reserved. * * ? 2007 Microsoft Corporation. All rights reserved. * * ? 2007 Microsoft Corporation. All rights reserved. * * ? 2007 Microsoft Corporation. All rights reserved. * * ? 2007 Microsoft Corporation. All rights reserved. * * * * * * * * * * * * * * * * * Use bridged networking:适合位于局域网环境的宿主机使用,可以在VMWare中通过Bridged Networking桥接式网络适配器与宿主机所在的局域网建立网络连接。这样,VMWare就可以像宿主机一样,与局域网中的其他计算机彼此相互访问了。使用Bridged Networking桥接式网络适配器要求虚拟机与宿主机处于同一个网段,换言之,虚拟机必须在局域网中拥有合法的网络标识。如果宿主机所在的局域网具有DHCP服务器,VMWare就可以自动获取合法的IP地址及默认网关、DNS服务器等网络参数,也可手动分配IP地址。此时虚拟机相当于网络上的一台独立计算机,与主机一样,拥有一个独立的IP地址。 Use network address translation(NAT):它适合使用拨号或虚拟拨号方式连接Internet的宿主机使用。Use network address translation(NAT)网络适配器无须在外部网络中获取合法的网络标识,VMWare将在宿主操作系统中添加一个叫做“VMWare DHCP”的服务,通过这个服务建立一个私有NAT网络,帮助虚拟机获取IP地址。此时虚拟机可以通过主机单向访问网络上的其他工作站(包括Internet网络),其他工作站不能访问虚拟机。 Use host-only network:可以将多台不同的VMWare与宿主机组成一个与外部网络完全隔绝的VMWare的专用网络,虚拟机与宿主机将把VMWare在宿主操作系统中安装的VMWare Ethernet Adapter for VMnet1虚拟网卡设置为host-only仅宿主式网络的虚拟交换机,无论是虚拟机还是宿主机都将通过VMWare在宿主操作系统中添加“VMWare DHCP”服务获取IP地址。此时虚拟机只能与虚拟机、主机互连,不能访问网络上的其他工作站。 Do not use a network connection:表示不为VMWare配置任何虚拟网络连接,此时虚拟机中没有网卡,相当于“单机”使用。 9)在“Network Type”窗口中单击“Next”选项,进入“Select I/O Adapter Types”窗口,如图3-42所示,在此窗口中设置I/O适配器的类型,建议选择系统的默认值。 10)在“S

文档评论(0)

1亿VIP精品文档

相关文档