冷冻机油特性供参习.docVIP

冷冻机油 1.技术规格????符合GB/T16630-1996标准要求。2.典型性能????本产品采用的是加氢油或烯烃合成油。凝点低，低温流动性好，氧化安定性好，使用寿命长。闪点高，不易蒸发，热稳定性好，抵抗积炭产生。3.主要技术要求 粘?度?等?级 22 32 46 68 运动粘度（40℃），mm2/s 19.8～24.2 28.8～35.2 41.4～50.6 61.2～74.8 闪点（开口），℃????不低于 150 160 160 170 倾点，℃????不高于 -35 -30 -30 -25 中和值，mgKOH/g????不大于 0.03 4.推荐应用?? ??四种牌号冷冻机油均适用于以氨为制冷剂的冷冻机。除22号油可用于二氧化碳制冷的冷冻机外，其它三个牌号还可用于氟里昂制冷剂的冷冻机。尺寸規格表 型號 牙制 適用電纜線徑 牙制外徑(mm) 包裝數量 CG-7B PG7 3~6.5mm 12.4 50 CG-9B PG9 4~8mm 15.2 50 CG-11B PG11 5~10mm 18.6 50 CG-13B PG13 6~12mm 20.4 50 CG-16B PG16 10~14mm 22.5 50 CG-21B PG21 13~18mm 28.3 50 CG-29B PG29 18~25mm 37.0 25 CG-36B PG36 22~32mm 47.0 　 CG-42B PG42 30~38mm 53.7 　 CG-48B PG48 34~44mm 59.0 　 　 YCB 0° YCL 90° YCH 45° YCB 0° YCL 90° YCB4 YCM YCN PCB 0° PCL 90° MAS PGG PFB PFL PGB PGL 90° YCT 90° YCS 0° U型管夾 MS-3102A MCS MS3057 MS25043 MS25042 CG TCG WL1 INSTALLATION INSTRUCTION  For Direct Fixing :Screw the nipple portion of the cable gland into housing tightly. In this case flat check nut is not required.For Fixing with lock nut: Wherever a blank hole is provided in the housing of the equipment, insert the nipple portion of the gland through this hole and fix it tightly by means of flat lock nut. Now pass the compression nut and the ring in succession ovre cable before commencing to terminate the cable. Then push the cable through the gland and tightly secure the compression nut. Due to pressure the ring will expand in radial direction so that it will have a tight grip over the outer sheath of cable thus effecting a dust proof entry of the cable. METRIC THREAD SKINTITE CABLE GLANDS NovoflexGlandPart No EntryThreadSize (mm) EntryThreadLength (mm) AcrossFlatsmm AcrossComersmm SeallingRange (mm) Standard Packing Min. Max. NG 16MS 16 10 20 22 6 8 50 NG 16M 16 10 20 22 8 12 50 NG 20MS 20 10 26 29 8 12 50 NG 20M 20 10 26 29 10 16 50 NG 25M 25 10 30 33 14 21 50 NG 32M 32 10 41 46 19 27 25 PG THREAD SKINTITE CABLE GLANDS NovoflexGlandPart No EntryT