铁矿选矿_毕业设计.doc

摘要 本次设计以张家洼铁矿选矿厂现场资料为依托，在满足设计任务书的基本要求下，以节能降耗、提高回收率的原则进行设计。为达到生产目的选择了最佳的辅助设施及生产设备，此外本次设计在选矿厂建设成本和之后的运营成本上也做到了最大化的节约。本设计的工作内容是：选厂工艺流程的选择及计算、矿浆流程的计算、设备的选型、绘制图形等。其中，通过现场考察确定磨矿分级过程采用自磨和闭路球磨。磁选定采用二段磁选，再磨后弱磁强磁联合，最大限度选出剩余铁矿。相对于铁，铜的经济价值较高，因此浮选流程采用一粗一精二扫来用以提高铜回收率，增加选厂收益。张家洼周边地形平坦，厂房布置采用平地布置，磁选、重选存在一定高度差，矿浆自流，节约输送成本。 关键词：设计，流程，计算 Abstract This design is based on the zhangs depression iron ore dressing plant site data, as well as meet the basic requirements to design to the principle of saving energy and reducing consumption, improve the recovery rate.In order to achieve production, chose the best auxiliary facilities and production equipment, in addition the design on the construction cost and operation cost of concentrator did to maximize savings.This design content is: mill plant process selection, calculation, pulp flow calculation, equipment selection, drawing, etc.Among them, grinding classification process by reference to the decision to adopt autogenous grinding and a closed circuit ball mill. Two section of magnetic separation, magnetic separation on the then weak magnetic strong magnetic joint after grinding, to select the maximum residual iron ore. Relative to the iron, the economic value of copper is higher, so the flotation process using one thick one fine two sweep to improve copper recovery rate, increase mill plant yield. Changs depression around the flat terrain, building layout using the ground is decorated, have a certain height difference, magnetic separation, gravity separation pulp gravity, save transportation costs. Keywords: design, process, calculate 目录 Abstract 1 目录 2 第一章 前序 9 1.1新建选厂的意义 9 1.2设计任务书 10 1.2.1设计目的 10 1.2.2设计题目 10 1.2.3设计内容 10 1.2.4主要技术指标和参数 11 第二章 鲁中冶金矿山公司的概况 12 2.1厂区交通、气候特点 12 2.2厂区状况及矿石性质 13 2.2.1小官庄矿体： 13 2.2.2张家洼矿体： 15 2.2.3港里矿体： 17 2.3选矿试验 17 2.3.1原矿分析： 18 2.3.2选矿试验结果 19 2.3.3选矿试验报告推荐意见 19 2.4厂区供电供水 19 2.4.1厂区供电 19 2.4.2厂区供水 21 第三章 方案设计及方案论证 22 3.1设计方案 22 3.2方案论证 23 第四章 干式磁预选流程计算和设备的选择 26 4.1干式磁预选流程的选择和计算 26 4.1.1计算干式磁预选工序小时