管螺纹标准参数.docVIP

英制螺纹标准规格表55°(非密封) (GB/T 7307-2001) 尺寸代号、每英寸牙数、螺距、螺纹直径 （in英寸）代号（n）牙数（p）螺距大径D d小径 D1 d1G1/16280.9077.7236.561G1/8280.9079.7288.566G1/4191.33713.15711.445G3/8191.33716.66214.95G1/2141.81420.95518.631G5/8141.81422.91120.587G3/4141.81426.44124.117G7/8141.81430.20127.877G1112.30933.24930.291G1-1/8112.30937.89734.939G1-1/4112.30941.9138.952G1-1/2112.30947.80344.845G1-3/4112.30953.74650.788G2112.30959.61456.656G2-1/4112.30965.7162.752G2-1/2112.30975.18472.226G2-3/4112.30981.53478.578G3112.30987.88484.926G3-1/2112.309100.3397.372G4112.309113.03110.072G5112.309138.43135.472G6112.309163.83160.872注：1英寸（in）=25.4mm 英制螺纹标准规格表55°(密封用圆锥管螺纹) (GB/T 7306.1、7306.2-2000) 尺寸代号、每英寸牙数、螺距、螺纹直径 （in英寸） 代号（n）牙数（p）螺距基准平面上的基本直径（mm）牙高 h （mm）装备 余量（mm）外螺纹长度（mm）大径D d小径 D1 d1有效长度基准距离ZG1/16280.9077.7236.561 0.581 2.5 6.5 4.0ZG1/8280.9079.7288.566ZG1/4191.33713.15711.445 0.856 3.79.76.0ZG3/8191.33716.66214.9510.16.4ZG1/2141.81420.95518.631 1.162 5.013.28.2ZG3/4141.81426.44124.11714.59.5ZG1112.30933.24930.291 1.479 6.416.810.4ZG1-1/4112.30941.9138.95219.112.7ZG1-1/2112.30947.80344.84519.112.7ZG2112.30959.61456.6567.523.415.9ZG2-1/2112.30975.18472.226 9.226.717.5ZG3112.30987.88484.92629.820.6ZG4112.309113.03110.07210.435.825.4ZG5112.309138.43135.472 11.540.128.6ZG6112.309163.83160.87240.128.6注：1英寸（in）=25.4mm Rc是新代号，“专”指英制螺纹密封锥管“内”螺纹。 而ZG是旧代号，他是指的英制螺纹密封锥管“内或外”螺纹。 R是新代号，“专”指英制螺纹密封锥管“外”螺纹。 ZG指的就是Rc和R的统称。