室内坐便器安装方法（五）.docVIP

室内坐便器安装方法（五） 室内坐便器安装方法（五）提要：对准座便器后尾中心，画垂直线，在距地面800毫米高度画水平线，根据水箱背面两个边孔的位置，在水平线上画印记 自建筑施工资料 室内坐便器安装方法（五） （1）取出地面下水口的管堵，检查管内确无杂物后，将管口周围清扫干净。 （2）将座便器出水管口对准下水管口，放平找正，在座便器螺栓孔眼处画好印记，移开座便器。 （3）在印记处打直径20毫米、深60毫米的孔洞，把直径10毫米螺栓插入洞内，用水泥捻牢，将座便器眼对准螺栓放好，使之与印记吻合，试验后将座便器移开。在座便器出水口及下水管口周围抹上油灰，再把座便器的四个螺栓孔对准螺栓，放平找正，螺栓上套好胶皮垫，拧上螺母，拧至松紧适度。 （4）对准座便器后尾中心，画垂直线，在距地面800毫米高度画水平线，根据水箱背面两个边孔的位置，在水平线上画印记，在印孔处打直径30毫米、深70毫米的孔洞。把直径10毫米、长100毫米的螺栓插入洞内，用水泥捻牢。将背水箱挂在螺栓上，放平找正，特别要与座便器中心对准，螺栓上垫好胶皮垫，拧上螺母，拧至松紧适度。 （5）安装背水箱下水弯头时，先将背水箱下水口和座便器进水口的螺母卸下，背靠背地套在下水弯头上，胶皮垫也分别套在下水管上。把下水弯头的上端插进背水箱的下水口内，下端插进座便器进水口内，然后把胶垫推到水口处，拧上螺母，把水弯头找正找直，用钳子拧至松紧适度。 （6）用八字门连接上水时，应先量出水箱漂子门距上水管口尺寸，配好短节，装好八字门，上入上水管口内。将铜管或塑料管断好，需娘灯叉的把弯娘好，然后将漂子门和八字门螺母背对背套在铜管或塑料管上，管两头缠油石棉绳或铅油麻线，分别插入漂子门和八字门进出口内，拧紧螺母。 自建筑施工资料 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality, psychologi