射水工法塑性砼防渗墙施工方法.docVIP

射水工法塑性砼防渗墙施工方法 射水工法塑性砼防渗墙施工方法提要：槽孔终孔验收合格后，即进行清孔换浆。清孔采用泵吸反循环法，即槽底抽吸，槽顶补浆。对于二期槽孔，用成型器侧向喷嘴及刷子清除砼壁上的泥皮 更多资源来 射水工法塑性砼防渗墙施工方法 ①轨道铺设 沿防渗墙轴线一侧铺设标准枕木，然后铺设钢轨，轨距以射水造墙机行走轨距确定。 ②造墙机就位、安装 沿射水造墙机行走方向用吊装设备依次将成槽机、砼浇筑机、砼搅拌机吊装就位，其中砂石泵和双吸离心泵分别置于成槽机前、后。 ③成槽 成型器下落，首先启动双吸泥浆泵，正循环系统射水工作，然后启动砂石泵，使用高速水流切割地层，上下往复运动成型器以进一步破坏土层，修整孔壁形成槽孔；成槽过程中不断抽入泥浆护壁。 ④清孔 槽孔终孔验收合格后，即进行清孔换浆。清孔采用泵吸反循环法，即槽底抽吸，槽顶补浆。对于二期槽孔，用成型器侧向喷嘴及刷子清除砼壁上的泥皮。 ⑤导管下设 槽孔长度一般为2～，下设、安装1套导管。导管内径为18～23cm，使用法兰连接。每套导管在开浇前下入可浮起的隔离球塞，堵塞导管底口。 ⑥砼浇筑 采用泥浆下直升导管法浇筑，先在导管内注入适量水泥砂浆，并在槽口附近准备足够量的混凝土，以使导管底口的球塞被挤出后，能将导管底端埋入混凝土内。混凝土由浇筑系统直接吊至导管口浇筑，浇筑过程中每30min测量一次混凝土面，每2h测定一次导管内混凝土面，在开浇和结尾时适当增加测量次数，并将每次的测量数据及时进行记录。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality, psychological quality and image quality. The formation of excellent moral education curriculum