打磨工的安全操作规程.docVIP

打磨工的安全操作规程 打磨工的安全操作规程提要：砂轮卡盘直径不得小于砂轮直径的1／3，卡盘与砂轮涧应垫上1～2毫米的软衬垫，其外径应比卡盘压紧面的直径大2毫米 地产e网 打磨工的安全操作规程 1．必须戴好防尘口罩及眼镜。 2．工作前，应检查砂轮有无损坏，安全防护装置是否完好，通风除尘装置是否有效。 3．安装砂轮前，必须核对砂轮允许的最高转速是否与主轴转速相适应，大于200毫米的砂轮应进行静平衡，不准使用裂纹或缺损的砂轮。 4．砂轮卡盘直径不得小于砂轮直径的1／3，卡盘与砂轮涧应垫上1～2毫米的软衬垫，其外径应比卡盘压紧面的直径大2毫米。 5．安装肘，应注意螺母的压紧程度，应压紧到砂轮转动时不产生滑动为宜，有多个压紧螺钉时，应按对角顺序逐步均匀旋紧。 6．砂轮装好后，必须将防护罩重新装好，再进行试转。直径小于400毫米的砂轮，应空转2分钟；直径大于400毫米的砂轮，应空转5分钟。砂轮转动时，不允许有明显振动。 7．调整砂轮防护罩及工件托架时，必须在砂轮停转后，方准进行。经常保持工件托架与砂轮的距离小于3毫米。 8．打磨时，应先起动吸尘装置，握牢工件，用力不得过猛，不准用杠杆推压元件，严禁站在砂轮正面操作，以防砂轮破裂伤人。 9．不是专门用于端面磨削的砂轮，禁止用端面进行打磨。 10．使府手持电动砂轮机打磨时，必须有牢固的防护罩和加设保护接零线或配用漏电保护器，并遵守电动手砂轮安全操作规程。 11．工作完毕后，应切断电源，确认砂轮停转后，方可离开岗位。 地产e网 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality, psychological quality and image quality. The formation of excellent moral education curr