暖通给水安装工程施工方法3.docVIP

暖通给水安装工程施工方法3 暖通给水安装工程施工方法3提要：丝接：采用丝扣连接的管道，丝扣螺纹应端正光滑、无毛刺，断丝缺扣不得超过螺纹全长的10%，螺纹松紧度适宜 于 暖通给水安装工程施工方法3 工程基本概况 系统名称管材连接方式保温防腐 采暖焊接钢管DN≤32焊接/DN＞32丝接岩棉管套暗装丹漆两道/明装加银粉两道 给水镀锌钢管丝接聚胺脂软管套明装银粉两道/暗装沥青漆两道 （二）施工方法 （1）安装前对各系统的所有管道和设备综合考虑，同时要熟悉与管道有关的土建、电气设备管线情况，做好施工前预想。 （2）采用分系统与分区域施工相结合的方法，各系统按先地下后地上、先干管后支管、先大管后小管、先里后外的施工工序进行。 （3）管道与部件尽量采用提前预制或工厂化加工，现场安装的方式。 （4）根据土建施工情况凡具备施工条件的应及早插入。 （5）为保证施工进度质量施工中各系统采取分段安装→试验→复验的方式。 （6）严格执行样板制，做好样板工序，样板间、样板层。 （7）设备吊装就位前须制定统一吊装方案，大型设备由专业起重人员吊运，并请厂家现场指导。 （三）基本操作方法 （1）丝接：采用丝扣连接的管道，丝扣螺纹应端正光滑、无毛刺，断丝缺扣不得超过螺纹全长的10%，螺纹松紧度适宜。接口填料可选用铅油麻丝或聚四氟乙烯生料带，安装完成后，联接牢固，管螺纹根部外露丝扣2-3扣，无外露麻头，防腐良好。 （2）UPVc管粘接：UPVc管采用粘接，粘接前应根据管件实测承口深度在管端标出插入深度，然后根据标记依次在承口内侧和插口外侧迅速、均匀、适量刷涂粘接剂后，立即找正方向将管子插至标记处，并旋转90℃，粘接后将挤出的胶粘剂擦净，粘接后的管段，应静置至接口固化为止，接口应整洁，牢固、密封。具体要求见行标cjj/T29-98。 （3）散热器安装：散热器经试验合格后方可进行安装，安装位置、标高须符合验标规定，散热器固定卡及立、支管卡架需提前预栽。待卡架稳固后进行安装。 于 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and