木门安装工程施工方法与技术措施.docVIP

木门安装工程施工方法与技术措施 木门安装工程施工方法与技术措施提要：在门窗框固定后，即可开始木门窗套饰面施工。木筒子板的门窗洞口应比门窗樘宽100mm，比门樘高50mm，比窗筒子板的门窗洞口应比门窗樘宽100mm 源自管理资料 木门安装工程施工方法与技术措施 1、立门框 （1）安装前对照楼层图纸、检查所有安装门窗的型号、规格、质量，凡不符合设计和施工规范要求的，预先整修或更换。 （2）弹好定位线，将门框塞入洞口就位，吊正、找直、找平，调整门框与墙面抹灰标筋面顺平，框子立挺锯口线与标记齐平，随即木楔临时固定，经复核无误后，用125mm圆钉，砸扁钉帽，双钉将木框钉牢于木砖上，框上勿显锤印。 2、安装门扇 （1）最好框口实际尺寸，在相应的门扇边缘弹好高宽线，将门扇塞入框内试装。合格后，取立梃高度的1/10在框扇上安装百页。 （2）每安装一扇门，反复开关，应轻便灵活，框扇平整，缝隙不超差为合格。 3、木门窗套的制作安装 （1）在门窗框固定后，即可开始木门窗套饰面施工。木筒子板的门窗洞口应比门窗樘宽100mm，比门樘高50mm，比窗筒子板的门窗洞口应比门窗樘宽100mm，是否方正垂直，预埋的木砖或连接铁件是否齐全，位置是否正确，如发出问题，必须修理或校正。 （2）制作安装木龙骨：根据设计要求和门洞口实际尺寸，先用木方制成龙骨架。一般骨架分三片，洞口上部一片，两侧各一片，每片一般分两根立杆，当筒子板宽度大于500mm需要拼缝时，中间应适当增加立杆。横撑间距不大于400mm，板厚为5mm时，横撑间距不大于300mm。横撑位置必须与预埋件位置对应，木龙骨架安装必须平整牢固，木龙骨刷水柏油两道，进行防腐处理。 （3）饰面板封钉：在完成门窗套木龙骨安装及墙面抹灰，并完成地面湿作业后，即可安装饰面板。门窗套木龙骨尺寸裁切饰面板，两端刨成45度角，安装时一般先钉横向，后钉竖向，钉长视板厚度而定，钉帽应砸扁，顺木纹冲入板表面1-3mm。 源自管理资料 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and