机组安装工艺质量目标.docVIP

机组安装工艺质量目标 机组安装工艺质量目标提要：表管和小口径管道敷设进行现场设计，尽量采取集中布置方式，管束布置应间距一致、均匀，整体美观，管束转向弯度美观大方 机组安装工艺质量目标 1建筑工程 施工工艺质量美观良好； 混凝土结构内实外光，棱角平直，接头平整； 防水工程无渗漏； 墙面垂直平整无裂纹； 地面工程平整、无裂纹、空鼓、无积水； 屋面工程坡度合理，排水畅通，水落管牢固美观，无积水，无渗漏； 装饰工程工艺美观； 沟（井）盖板齐全、平整、周边顺直； 2安装工程 对本工程内所有管道、管道支架、钢结构在防腐涂第一遍前，对其金属表面进行除锈处理； 所有阀门在安装前根据国家有关规定和业主要求进行必要的阀门水压试验和必要时解体检查； 锅炉钢结构构件无变形，高强螺栓连接紧固，且方向保持一致，涂装外观涂刷均匀，色泽一致，有明显的沉降观测点； 表管和小口径管道敷设进行现场设计，尽量采取集中布置方式，管束布置应间距一致、均匀，整体美观，管束转向弯度美观大方、一致，管束坡度符合标准、规范的要求；固定支架间距均匀一致，横平竖直，吊架垂直； 设备安装整齐、布置合理，设备保持清洁，无损伤，无遗留物。设备爬梯平台栏杆牢固可靠，平整，无扭曲，拐弯处平滑过度，外观美观； 所有的管道、管道支架、钢结构在防腐涂漆第一边前，应对其金属表面进行除锈喷砂处理。 电气和仪表盘柜安装垂直、排列整齐、间距均匀，垫片放置合理、美观； 接地系统安装工艺规范、美观。 照明线路布置合理，灯具及配电箱位置正确、固定牢靠，安装工艺精美，确保照明投入率100%。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality, psychological quality and image