模板工程施工方法.docVIP

模板工程施工方法 模板工程施工方法提要： 更多精品：总结 一、本工程框架梁、板支模主要采用18厚七夹板，支撑采用∮50~∮60的钢顶管或硬木支承，做到各构件模板有足够的强度、刚度及稳定性，确保各构件的尺寸及相互间位置的正确。拼制模板时，板边要找平刨直，不使漏浆，浇灌砼前应充分用水湿润，并派专人看护模板是否有松动、移位现象，及时处理。 二、柱模: 现场拼装，柱模竖向固定用50*100木枋材，每隔500mm加柱箍一道，柱箍用∮14螺栓与木制水平背杠对接以控制截面。柱模下部留出活口，浇砼前清理柱中杂物干净后封紧，楼层上预埋∮20@500的钢筋定位桩以定位柱模，亦可防止柱根部浇砼时移位，详见《主要构件支模图》。 三、梁板模板: 支撑的钢顶间距不大于1000，次梁不大于800，主梁不大于600，对于跨度大于或等于4m的梁和板，模板应起拱，起拱高度为全跨长度的3/1000，详见《主要构件支模图》。 四、楼梯模板: 楼梯模板施工前根据实际层高放样，先安装平面梁及基础模板，再装楼梯底模板，然后安装楼梯外侧板，外侧板应在其内侧弹出楼梯底厚度线，用套板画出踏步位置线，钉好固定踏步侧板的挡木，在现场装钉侧板，楼梯模板构造详见《主要构件支模图》。 五、特殊部位支模 六、模板的拆除: 拆模时不能用力过猛过急，拆下的模板应及时运走，及时清理干净模板表面的砼泥浆，刷隔离剂，保证模板不受损失，提高模板周转次数和保证砼质量。拆模的顺序一般是后支的先拆，先支的后拆，先拆除非承量部分，再拆除承重部分。 柱和梁侧模板拆除要在砼强度能保证表面及棱角不因拆模面而损坏后，方可拆除;跨度大于8m的梁板和悬挑构件在砼强度达到100%，且上部无施工荷载时，方能拆模;对于跨度小于8m的现浇砼梁板砼强度达到75%，方可拆模。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students