聚乙烯管施工方案.docVIP

聚乙烯管施工方案 本文提要：聚乙烯管施工的操作工人上岗前，必须经过专门培训，经考试和技术评定合格后，方可上岗操作。聚乙烯管施工焊接方式采用：电热熔承插连接。 .所有管道材料应具有质量检验部门的产品质量检验报告和生产厂家的合格证。 2.管材、管件存放和搬运时,用非金属绳或钢带捆扎并加垫保护。不得抛摔﹑剧烈撞击﹑爆晒﹑雨淋和沿地拖拽,不得与油类﹑酸﹑碱﹑盐等化学物质接触。 3.管沟的开挖程序与要求与钢管要求相同,聚乙烯管道沟槽底部宽度为:B=D+~。 4.聚乙烯管施工的操作工人上岗前,必须经过专门培训,经考试和技术评定合格后,方可上岗操作。 5.聚乙烯管施工焊接方式采用:电热熔承插连接。 6.聚乙烯管施工程序及方法: ⑴.检查管子端头是否被划伤、碰坏;管材的连接端切割是否垂直。检查合格后,才可进行下一步操作。 ⑵.电熔承插连接前,应校直两对应的连接件,使其在同一轴线上。 ⑶.清除两管口及电熔接头内的灰土、水及其他异物,并用洁净棉布擦拭干净。 ⑷.在要焊接的管子或管件端头,用划线板量出一定长度,并作好记号。 ⑸.把电熔接头预先插入管子端头,使其外沿与记号对齐,然后把另一管头插入电熔接头。 ⑹.将插入接头的管子端面紧贴对齐。 ⑺.用表测焊机输入端电压,是否在220±20V范围内,如不在此范围内,停止焊接。 ⑻.将焊机的插头分别与电熔接头的接线柱连接,准备进行焊接,焊接工艺根据现场的环境温度湿度及其他影响因素专门给出。 ⑼.焊接完毕后,如果电熔接头处没有受其他外力,在30min后即可取下扶正器。否则要等到手感温热不烫,才可取下扶正器。在电熔接头没有完全冷下来的时候,不许强力拉动或弯曲管子。 ⑽.上述操作完毕后即可进行下一步操作。 ⑾.管道施工中,应及时对电熔套筒用油漆笔进行编号,并做好施工记录以便对施工质量进行跟踪。 ⑿.聚乙烯管与金属管或其他管子连接时,采用钢塑转换接头连接。 ⒀.聚乙烯管施工时距管顶大于300mm处应埋设燃气专用警示带。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, h