钢筋弯曲机安全操作规程（五）.docVIP

钢筋弯曲机安全操作规程（五） 钢筋弯曲机安全操作规程（五）提要：作业时将钢筋需弯的一头插在转盘固定销的间隙内，另一端紧靠机身固定销，并用手压紧，检查机身销子确实安在挡住钢筋的一侧，方可开动 钢筋弯曲机安全操作规程（五） 1、工作台和弯曲机台面要保持水平，并准备好各种芯轴及工具。 2、按加工钢筋的直径和弯曲半径的要求，装好相应规格的芯轴和成型轴、挡铁轴或可变挡架，芯轴直径应为钢筋直径的倍，挡铁轴应有轴套。 3、挡铁轴的直径和强度不得小于被弯钢筋的直径和强度。不直的钢筋，不得在弯曲机上弯曲。 4、应检查并确认芯轴、挡铁轴、转盘等无损坏及裂纹，防护罩紧固可靠，经空运转后确认正常方可作业。 5、作业时将钢筋需弯的一头插在转盘固定销的间隙内，另一端紧靠机身固定销，并用手压紧，检查机身销子确实安在挡住钢筋的一侧，方可开动。加工较长的钢筋时，应有专人帮扶，并听从操作人员指挥，不得任意推拉。 6、作业中，严禁更换芯轴、销子和变换角度以及调整等作业，亦不得加油或清扫。 7、在弯曲未经冷拉或带有锈皮的钢筋时，应戴防护镜。 8、弯曲高强度或低合金钢筋时，应按机械铭牌规定换算最大允许直径并应调换相应的芯轴。 9、在弯曲钢筋作业半径内的机身不设固定销的一侧严禁站人。弯曲好的半成品应堆放整齐，弯钩不得朝上。 10、对超过机械铭牌规定直径的钢筋严禁进行弯曲。 11、维修保养或转盘换向时，必须在停稳拉闸断电后进行。 12、作业后应及时清除转盘及插入座孔内的铁锈、杂物等。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality, psychological quality and image quality. The formation of excellent moral education curriculum