钢筋操作工艺要求-梁钢筋施工工艺.docVIP

钢筋操作工艺要求:梁钢筋施工工艺 钢筋操作工艺要求:梁钢筋施工工艺提要：先穿主梁的下部纵向受力钢筋，将箍筋按已画好的间距逐个分开；穿次梁的下部纵向受力钢筋，并套好箍筋 更多精品来自保安 梁钢筋： ⑴工艺流程： ⑵在梁底模上画出箍筋间距，摆放箍筋。 ⑶先穿主梁的下部纵向受力钢筋，将箍筋按已画好的间距逐个分开；穿次梁的下部纵向受力钢筋，并套好箍筋；放主次梁的架立筋；隔一定间距将架立筋与箍筋绑扎牢固；调整箍筋间距使间距符合设计要求，绑架立筋，再绑主筋，主次梁同时配合进行。 ⑷框架梁上部纵向钢筋应贯穿中间节点，梁下部纵向钢筋伸入中间节点锚固长度及伸过中心线的长度应符合设计要求。框架梁纵向钢筋在端节点内的锚固长度也应符合设计要求。 ⑸绑梁上部纵向筋的箍筋，宜用套扣法绑扎。 ⑹箍筋在叠合处的弯钩，在梁中应交错绑扎，箍筋弯钩为1350，平直部分长度为10d。 ⑺梁端第一个箍筋应设置在距离柱节点边缘50mm处，梁端与柱交接处箍筋应加密，其间距与加密区长度均要符合设计要求。 ⑻在主、次梁受力筋下均应垫垫块，保证保护层的厚度，受力筋为双排时，可用短钢筋垫在两层钢筋之间，钢筋排距应符合设计要求。 ⑼框架梁纵向钢筋的连接 本工程框架梁纵向主筋直径大于Ф20时，采用直螺纹连接接头；主筋直径小于等于Ф20时，采用绑扎搭接连接。直螺纹连接接头详见直螺纹连接施工工艺；采用绑扎搭接时，搭接长度要符合规范规定。在规定搭接长度的任一区域内有接头的受力钢筋截面面积占受力钢筋总截面面积百分率，受拉区不大于50%。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality, psychological quality and image quality. The formation of excellent moral education c