门窗工程通病的防治.docVIP

门窗工程通病的防治 门窗工程通病的防治提要：门窗扇翘曲1)门窗扇立面不在同一个平面内。2)门窗扇安装后关不平,插销插不进销孔内。 来自物业管理资料下载 门窗工程通病的防治 第一节 门窗框变形 门窗框制作好后,边梃、上下槛、中贯档发生弯曲或者扭曲、反翘,门窗框立面不在一个平面内。立框后,与门窗框接触的抹灰层挤裂或挤脱落,或边梃与抹灰层脱开。轻者门窗扇开关不灵活;重者门窗扇关不上或关上拉不开,无法使用。 门窗框拼装好后发生变形,对弓形反翘、边弯的木材可烘烤凸面使其平直。 将变形严重的框料取下,重新换上好料。 第二节 门窗扇翘曲 门窗扇立面不在同一个平面内。 门窗扇安装后关不平,插销插不进销孔内。 调整合页在框立梃上的横向位置,使扇上销或插销的一边与框平齐。 扇与框过紧部分进行修创。 用门锁或插销对翘曲门扇进行校正。 第三节 门窗框（扇）割角拼缝不严 在门窗框的边挺与上、下槛,门窗扇的冒头与扇梃,门窗棂子与冒头、扇梃等结合处不严密，有明显的缝隙,或在倒棱割角处不密合。 如系半榫过长,可略去一些,使其距眼底3mm,也可将眼适当补凿加深。 若榫肩不方正,应视情况将其修理方正,如榫肩过短,则需更换。 如为双榫、双夹榫因“叠台”过长而造成缝隙不严,可将“叠台”部分适当锯短。 割角结合缝不严时,可用小木楔粘胶塞缝,胶干后再按结合处的线条情况仔细削磨与两边完全一致为止。 第四节 钢门窗翘曲变形 钢门窗框翘曲;框、扇料弯曲变形,关闭不严密,或者扇与框摩擦和卡住。 如发现钢门窗变形,可根据变形情况进行调直处理。 如门窗框或窗扇的梃子、棂子发生局部弯曲变形,可用氧气等加热烘烤,进行局部正。 来自物业管理资料下载 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideolog