冷轧专业英语.docx

冷轧常用专业词汇表一、首钢京唐（酸轧机组）常用词1.entry W/B conveyor入口步进梁运输机2. entry coil turner旋转台3.entry coil car入口钢卷车4.pay off reel开卷机5.processor处理器6.coll opener开卷器7.ertry shear with pinch roll入口剪带夹送辊8.scrap disposal equipment废料处理装置9.deflector pinch roll转向夹送辊10. deflector roll转向辊11.welder焊机12.notcher月牙剪13.side guide边部对中14.bridle roll张力辊15.steering roll纠偏辊16.tension meter roll张力计辊17.tension leveller拉伸破磷机18.entry wringer roll入口挤干辊19.dryer干燥器20.side notcher月牙剪21.hold down roll压辊22.side trimmer切边剪23.scrap chopper碎边剪24.scrap conveyor废料运输带25.burr masher去毛刺机26.mill轧机27.mill motor轧机主电机28.rotary shear飞剪29.carrousel reel张力卷取机30.inspection table检查台31.sleeve bucket transfer car套筒运输车32.delivery coil conveyor出口步进梁运输机33.skid鞍座34.nozzle喷嘴二、浙江东南1.Reversing Cold Mill (RCM)可逆式冷轧机2. Motor Control Center (MCC)电机控制中心3. E-house电器室4. transformer变压器5. skin pass mill (或temper mill)平整机6.product mix产品大纲7.coil weight卷重8. stack weight垛重9.workbase炉台10. Specific coil weight卷材单重11. inner cover内罩12. heating bell加热罩13. cooling bell冷却罩14. filter mesh过滤器网15. pressure switch压力开关16. isolating unit隔离装置17. control relay控制继电器18.emulsion room乳化液站19. combustion燃烧20. butterfly valve蝶形阀21. Safety Equipment安全设备22.roll chock轴承座23.Spraying header喷淋水管（喷淋头）24.Mill stand piping轧机机座管系(管线)25. Drive spindles驱动轴26. Cross cut shear横剪机组27. Pivot枢轴28. Coil car卷材移动台车29. Segments（胀缩式卷筒）扇形体30.Snubber roll缓冲辊31.Groove凹槽32. flange法兰33. Shape Measuring Roll板形仪34. Delivery (entry)Tension Reel出(入)口卷取机35. Foundation Bolts and Nuts基础螺栓36. Interconnecting piping中间管线37.Gear Coupling齿轮联轴器38. Load test负载测试39.Breakage断带40.Stoppage停车cold rolled:冷轧的, 冷态滚压的cold rolled steel sheet: 冷轧薄钢板cold rolled coil:冷轧薄卷electrical steel sheet:电工钢（片）uncoiler:开卷机reheating furnace: 再加热炉cold leveling:冷平整，冷矫正pickling:酸洗cold rolling mill:冷轧机electrolytic cleaner:电解清洗液preheating:预热soaking cooling:均匀退热rapid cooling: 快速冷却over aging: 过时效,老化过度final cooling: 最后冷却continuous annealing line：连续退火线recoiling：重绕temper rolling: 硬化冷轧, 表面光轧, 平整batch annealing line:成批退火线cold rolled coil:冷轧薄板side tri