- 1、本文档共33页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
长安铃木天语SX4原厂维修手册发动机机械部分解读
1-1. Engine Mechanical -M16A- 发动机机械部分 凸轮轴 气门间隙的技术要求 冷态时(冷却液温度为15-25℃):进气0.18-0.22 mm 排气0.28 - 0.32 mm 热态时(冷却液温度为60-68℃):进气0.21-0.27 mm 排气0.30 - 0.36 mm 气缸垫 缸 体 曲轴支承结构 ●整体铸造:刚性好,成本高 ●轴承盖:刚性差,成本低 曲轴轴承盖(M系列与G系列)的比较 曲轴轴承盖 轴承盖 曲轴 连 杆 正时链条 正时链 15. TIMING CHAIN (cont.) 静音链条 滚针链条 滚针链条 静音链条 在4000RPM至6000RPM时,噪音显著区别 1. 深蓝色标 2. 三角形标志 3. 黄色色标 4. 圆点标志 5. 大约 60o 6. 大约30o Looking at only the pitch (p), the M16A engine looks like a 2-litre engine. The pitch of M engines is relatively bigger due to water jacket. As already described, M16A has an open head type cylinder block. Valve angle is 29 degrees. The intake port could be designed, in order to erect as much as possible, against combustion chamber. Due to the above, intake air is directly admitted into the combustion chamber. Then it may form the TUMBLE FLOW in it. The tumble flow will increase combustion efficiency and burning velocity. The valves are lifted by cam through a tappet directly. The M engine has been reduced in mechanical friction, compared with rocker arm mechanism. The plastic range tightening bolt is used as a cylinder head bolt. As this type of bolt is a plastic deformation bolt, it should be inspected before reuse. The same type of bolt is used for main bearing cap and connecting rod. The method of inspection is described later. Before reusing plastic tightening range bolts, check them for deformation. Measure diameter at points “a” and “b”. The difference between obtained values “A” and “B” should be less than 0.1mm. If “A”-”B” exceeds this service limit, the bolt should be replaced with a new one. When tightening 10 pcs. of the cylinder head bolts, you have to go through four (4) steps. 1st step, all bolts shall be tightened in the torque of 20Nm (2.0kg-m) diagonally. 2st step, all bolts shall be further tightened in the torque of 40Nm (4.0kg-m) diagonally. 3rd step, all bolts shall be turned clockwise 60 degrees clockwise. 4th step (last step), all
您可能关注的文档
- 问题员工的管理技巧.ppt
- 闸北培训机构新王牌 最好的中考补习班初三化学补习班-空气.doc
- 问题解决及8D步骤与客诉处理.ppt
- 阀门基础培训.ppt
- 阅读文章和掌握审题答题技巧一.doc
- 阅读理解解题技巧.ppt
- 阀门识培训教材(锅炉用阀门).ppt
- 长度单位、质量单位练习课.ppt
- 防寒过冬安全管理措施.doc
- 包孝肃奏议集.doc
- 分析let s单元56ago2卷纸zheng unit56.pdf
- 塑胶材料其它分类原料pa9t 12.pdf
- md16x16数字媒体切换器设备.pdf
- 者参考项目发起人学科类型单位序列承包商修订页代码顺序典型.pdf
- 届世界天然气大会阿姆斯特丹2006add10288.pdf
- 期测试记录表每周weekly g1g6 journeys tests level 6 lesson26.pdf
- modernize-whitepaper现代化您应用程序白皮书.pdf
- anybackup产品典型案例分析.pdf
- 约克金融工程课程tfeslide32.pdf
- 广州市妇女儿童医疗中心历份教学药历01tjy.pdf
最近下载
- 2024年湖北省中考历史试题卷(含答案及解析).docx
- 爱护我们的五官幼儿主题班会PPT课件.pptx VIP
- 2020人教版二年级数学下册易错题型及答案.pdf VIP
- 2024届高考专题复习:小说叙述视角课件(共24张PPT) (1).pptx VIP
- 2024届高考专题复习:小说叙述视角.pptx VIP
- 《道德与法治》六年级下册全册知识点汇总.docx
- 测测达人版平台服务规则考试题库答案APP测测基础认证题.docx
- 江苏省苏州常熟市七年级数学下学期期末考试试题.docx VIP
- 建筑地基处理技术规范.pptx
- T_CACM 1270-2019 中医内科临床诊疗指南 脓毒症.docx
文档评论(0)