模具结构英语).docVIP

机械英语专用词汇 模具专业英语[分享] 模具述语一、入水：gate进入位：　gate location? ? 水口形式：gate type大水口：edge gate? ?? ? 细水口： pin-point gate水口大小：gate size? ???转水口：　switching runner/gate唧嘴口径：　sprue diameter二、流道: runner热流道：　hot runner,hot manifold? ?热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate? ?? ? 圆形流道：round(full/half runner流道电脑分析：mold flow analysis? ???流道平衡:runner balance热嘴：　hot sprue? ?? ?? ?热流道板：hot manifold发热管：cartridge heater? ???探针: thermocouples插头：　connector plug? ? 插座： connector socket? ?密封/封料： seal三、运水：water line喉塞：line plug? ?? ?? ?喉管：tube塑胶管：plastic tube? ? 快速接头：jiffy quick connector plug/socker四、模具零件：　mold components三板模：3-plate mold? ???二板模：2-plate mold边钉/导边：leader pin/guide pin? ?边司/导套：bushing/guide bushing中托司：shoulder guide bushing? ? 中托边L：guide pin顶针板：ejector retainner plate? ? 托板：　support plate螺丝： screw? ?? ?管钉：dowel pin? ? 开模槽：ply bar scot内模管位：core/cavity inter-lock? ???顶针：　ejector pin司筒：ejector sleeve? ??司筒针：ejector pin推板：stripper plate? ? 缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock? ???斜顶：lifter模胚（架）： mold base? ???上内模：cavity insert下内模：core insert? ?? ? 行位（滑块）： slide镶件：insert? ?? ? 压座/斜鸡：wedge? ?耐磨板/油板：wedge wear plate? ???压条：plate? ? 撑头: support pillar? ?唧嘴： sprue bushing挡板：stop plate? ?定位圈：locating ring? ? 锁扣：latch扣鸡：parting lock set? ?推杆：push bar? ???栓打螺丝：S.H.S.B顶板：eracuretun? ? 活动臂：lever arm? ? 分流锥：spure sperader水口司:bush? ?垃圾钉：stop pin? ? 隔片：buffle弹弓柱：spring rod? ?弹弓:die spring? ?中托司：ejector guide bush中托边：ejector guide pin? ?镶针：pin? ? 销子：dowel pin波子弹弓：ball catch? ?喉塞: pipe plug? ?锁模块：lock plate斜顶：angle from pin? ? 斜顶杆：angle ejector rod尼龙拉勾：parting locks? ?活动臂：lever arm复位键、提前回杆：early return bar? ? 气阀：valves斜导边：angle pin? ?术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： u