150万吨年渣油催化裂化反应再生系统工艺设计本科学位论文.doc

150万吨/年渣油催化裂化反应再生系统工艺设计 摘 要 在本设计中，使用大庆常压渣油作为原料，采用汽油生产方案，进行渣油催化裂化反再系统的工艺设计。 催化裂化装置由反应再生系统，分馏系统，吸收稳定系统和能量回收系统组成。本设计主要针对反再系统进行设计计算。由于渣油催化裂化的焦炭产率高，对再生器的烧焦能力要求较高，故本设计选用烧焦罐式再生器以实现高效完全再生。 0.1%以下，充分发挥了催化剂的选择性，延长了催化剂的寿命。 关键词：催化裂化，提升管，再生器，催化剂 TECHNOLOGCIAL DESIGN FOR REACTION AND REGENERATION SYSTEM OF 150wt/a RFCC Abstract Reaction and regeneration system technology of a 270wt/a RFCC processing DAQING atmospheric residue feedstock has been designed and calculated in this layout. The catalytic cracking unit is made up from reaction and regeneration system fractionation system， absorption and stabilization system and energy recover system. This layout is derected against reaction and regeneration system to compute.A high efficient and complete coke burning regenerator having high burning capacity was adopted because much coke was produced during RFCC process. In the design，eferring to the dates of feed and the same type reactors， I design a high-low parallel FCC reactor-regenerator system-riser reactor and coke container high temperature complete reactor-regenerator system.he part of reaction: the reactor develops sufficient room for feed oil and catalytic contacting completely. This kind of design is to reduce coke promote recall ratio of light oil. The part of regenerator system: the regenerator can burn up remaining carbon about catalytic to recover activity of CAT. General speaking， my design can reduce the ratio of carbon in CAT to 0.1%，so it makes full use of choice of CAT， extend the life of the catalyst. Keywords: catalytic cracking， riser， 目录 1 文献综述 1 1.1催化裂化工艺产生的背景及意义 1 1.1.1国外催化裂化 1 1.1.2国内催化裂化 2 1.2催化裂化技术的现状及发展 2 1.2.1国外催化裂化技术的现状及发展 3 1.2.2我国催化裂化技术的现状及发展 5 1.3重油催化裂化 7 1.3.1重油催化裂化的原料 8 1.3.2重油催化裂化的产品 8 1.3.3重油催化裂化装置特点 8 1.4催化裂化装置研究进展 11 1.4.1催化裂化再生装置形式 11 1.4.2催化裂化反应装置形式 15 1.4.3催化裂化反应—再生两器排布方式 19 1.4.4提升管末端快速分离器 21 1.4.5进料雾化喷嘴 24 1.4.6空气分布器 26 1.4.7结语 29 2 设计说明 30 2.1 加工方案的确定及装置形式的选择 30 2.1.1 加工方案 30 2.1.2 装置形式的选择 30 2.2 流程说明 30 2.2.1 反应再生系统 30 2.2.2 分馏系统 32 2.2.3