AEM5700防霉抗菌剂使用指南.pptVIP

維護您和您擁有的產品永保清新潔柔PROTECTS THE PRODUCTS THAT PROTECT YOU AEM 5700 Spray 施工技术指导AEM 5700 Spray Application Instruction 三、機具設備 Details Equipment 2. 裝有AEM5700 Spray的容器 AEM5700 Spray Container (1)封口至桶底需用硬管固定：圖A Insert and stabilize a rigid tube from the opening to the bottom. (Photo A) (2)再以軟管與噴槍連接：圖B Connect with a hose and a spray gun. (Photo B) 3. 電動空壓機 Auto air compressor 四、建議施工製程 Suggested Spray Procedure 1. 鞋子成型後, 未塞紙團前, 施以AEM5700 Spray 加工。 Spray AEM5700 after lasting and prior to heating (without stuffing paper). 五、操作標準化 (一般鞋面材質)Operation Standardization (General upper material) (一)、噴槍調整 Spray gun adjustment (二) 操作七步驟 Seven Operation Steps 1. 試將噴壓及噴量調整至最霧狀 Adjust pressure and volume to the optimum mist. 2. 上蠟天然皮革 Waxed natural leather (1)噴灑 (2)正確及錯誤噴灑樣品之比較 (1)Spraying (2) Comparison 3. PU亮面合成皮 Patent PU leather (1)噴灑 (2)正確及錯誤噴灑樣品之比較 (1)Spraying (2) Comparison 七、附註－製程上常見錯誤操作Remarks- General mistakes in Spraying 1. 操作人員未戴口罩 Without wearing mouth mask. 2. 未裝有抽風設備 Hood absence. 3. 噴槍設備的選擇不當 Spraying facility is not proper. 4. 噴壓的調整 (過大) Air flow adjustment (too high). 5. 噴幅的調整 (過大) Spraying width adjustment (too wide). 6. 不適當的噴灑距離 (太近或太遠) Spraying distance unsuitable. 7. 鞋子上水滴的產生 Spots happen on the surface. 8. 噴灑過量致水痕產生 Water marks caused by over spraying. 9. 成型塞紙團後，進行加工Spraying after stuffing. 10. 鞋間隔不足，導致內緣噴塗不均 Inside with poor uniformity. caused by less distance between shoes. 国际通用认证报告 * Bacterial Dust Mite Bacterial Mold Spores Spores Bacterial Dust Mite Bacterial AEM 5700 Spray 产品說明会 AEM 5700 Spray 2006 Presentation 引言Lead-in 一、施工方法： Method 人員配戴口罩以噴槍將AEM5700 Spray均勻的噴灑於需噴灑之部位 ，而達長效防護型抑菌防黴效果。 Before using spray gun, the operator has to wear specific mask. The AEM5700 uniformity is necessary to ensure antimicrobial efficacy. 二、標準配置圖Standard Facility 1.噴槍裝置 Spray gun 圖 B 圖 A 4. 抽風設備 Hood 2. 再進烘箱完全乾燥，達有 效的抑菌防黴加工