工程机械性手册吊车.doc

小湾建设公司 工程机械性能手册 吊 车 张建军 汇编 二○○四年三月十六日  目 录 1 50吨全液压汽车吊(徐州重型机械厂) 1 2 50吨履带式起重机(徐州重型机械厂) 2 3  50吨全液压汽车吊 徐州重型机械厂50吨? 型号：QY50B 全液压汽车吊起重机起重作业之前，必须完全支好支腿，必要时包括第五支腿，可以360度全回转起重作业.起露作业时应选择合适的钢丝蝇倍率，起升钢丝蝇单绳拉力应不大于4200kg．臂端单滑乾的起重性能同5.1m副臂(o·)安装角，量大起重量为4吨．二、外形尺寸 三、性能表 表中所示的起重量包括吊具和附件的重量．表中粗线以上起重量由起重机强度决定，粗线以下的起重量由起重机稳定性决定． 五、工作范围图  50吨履带式起重机徐州重型机械厂50吨 型号：QUY50 履带式起重机履带式起重机最大起重量50吨，主臂长13—52米、副臂长9.15—12.25米。能够带载行驶，并可在360‘范围内全方位吊装。 二、主要技术参数 三、主臂技术参数 三、性能表付臂 四、倍率及吊钩 五、工作范围图  100吨履带式起重机日本住友 100吨 型号：LS-418J 履带式起重机履带式起重机最大起重量100吨，主臂长58米、副臂长18.3米。能够带载行驶，并可在360‘范围内全方位吊装。钩头重量：100吨用1.04吨、65吨用0.79吨、35吨用0.8吨、9吨用0.26吨钩头 二、主臂技术参数1 三、主臂技术表2 四、付臂技术参数  Ellipticity of elbow pipes with diameters less than or equal to 150 mm must be not greater than 8% diameter of 200 mm or less shall not be greater than 6%. Wall thickness of the pipe wall thinning rate must not exceed the original 15%. Crease roughness: diameter 125 mm or less, shall not exceed 3 mm diameter less than or equal to 200 mm, not more than 4 mm. 7.3.9 simmering bending production of square steel tube extension, to use the whole tube bending. Interface if necessary, the welding position should be located in the middle of the vertical arm. 7.3.10 install expansion joints should be done. If design is not required, pipe compensator lengthen should conform to the requirements in the following table: square scale length δ x is equal to 1/2. Pre stretch tolerance: casing + 5 mm, +10 mm. 7.3.11 pipe form, location, spacing shall meet the design and specifications. 7.3.12 piping on back or return pipe at higher levels of the upper to automatic valve to install a drain valve below the horizontal parts. 7.3.13 supports and hangers of checks and the number 1) hanger installed must be checked before installation of supports and hangers part models, specifications of springs setting values, whether the materials meet the requirements of drawings and documents; 2) supports and hangers of material, size and accuracy shall