stm32驱动ADS7843(国外英语资料).docVIP

stm32驱动ADS7843(国外英语资料) # include“stm32f10x_lib.h” # include“integer.h” # include“touch.h” # include“TFTdriver.h” #定义cstouch_h gpiob - BSRR = GPIO_Pin_0 即# define CSTOUCH_L GPIOB - = GPIO_Pin_0 #定义get_pen_int(GPIOB - IDRGPIO_Pin_12) 空白Touch_Config(空白) { SPI_InitTypeDef SPI_InitStructure; GPIO_InitTypeDef GPIO_InitStructure; RCC_APB1PeriphClockCmd(RCC_APB1Periph_SPI2,使); RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB,使); / * PB15-MOSI2、PB13-SCK2 PB14-MISO2 * / GPIO_InitStructure。gpiopin13 gpiopin14 gpiopin15; GPIO_InitStructure。GPIO_Speed = GPIO_Speed_50MHz; GPIO_InitStructure。GPIO_Mode = GPIO_Mode_AF_PP; GPIO_Init(GPIOB GPIO_InitStructure); / * PB0-CS * / GPIO_SetBits(GPIOB GPIO_Pin_0);/ /预置为高 GPIO_InitStructure。GPIO_Pin = GPIO_Pin_0; GPIO_InitStructure。GPIO_Speed = GPIO_Speed_50MHz; GPIO_InitStructure。GPIO_Mode = GPIO_Mode_Out_PP; GPIO_Init(GPIOB GPIO_InitStructure); / * PB12-INT,输入* / GPIO_InitStructure。GPIO_Pin = GPIO_Pin_12; GPIO_InitStructure。GPIO_Mode = GPIO_Mode_IPU;/ /上拉 GPIO_Init(GPIOB GPIO_InitStructure); / * * / SPI2配置 SPI_Cmd(SPI2,禁用);/ /必须先禁能,才能改变模式 SPI_InitStructure。SPI_Direction = SPI_Direction_2Lines_FullDuplex;/ /两线全双工 SPI_InitStructure。SPI_Mode = SPI_Mode_Master;/ /主 SPI_InitStructure。SPI_DataSize = SPI_DataSize_8b;/ / 8位 SPI_InitStructure。SPI_CPOL = SPI_CPOL_High;/ / CPOL = 1时钟悬空x SPI_InitStructure。SPI_CPHA = SPI_CPHA_2Edge;/ / CPHA = 1数据捕获第x SPI_InitStructure。SPI_NSS = SPI_NSS_Soft;/ /软件NSS SPI_InitStructure。SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_16;/ / 32米/ 16 = 2 m SPI_InitStructure。SPI_FirstBit = SPI_FirstBit_MSB;/ /高位在前 SPI_InitStructure。SPI_CRCPolynomial = 7;/ / CRC7 SPI_Init(SPI2 SPI_InitStructure); SPI_Cmd(SPI2,使); } 静态与SPIByte(与字节) { 在没有emplty/登记的时候 而(SPI_I2S_GetFlagStatus(SPI2 SPI_I2S_FLAG_TXE)= =重置); /通过SPI2外围/发送字节 SPI_I2S_SendData(SPI2字节); /等待接收一个字节/ 而(SPI_I2S_GetFlagStatus(SPI2 SPI_I2S_FLAG_RXNE)= =重置); /返回从SPI总线/读取的字节 返回SPI_I2S_ReceiveData(SPI2); } u16 X_Buf[10],Y_Buf[10]; 静态与LCD_BufX; 静态u16 LCD_BufY; / * * * * * * * * * * * *