45度角度头设计与仿真.docVIP

45度角度头设计及仿真 [摘要] 角度头是一种机床附件。安上后刀具旋转中心线可以与主轴心线成指定的角度加工件，无需改变机床结构就可以增大其范围和适应性并能减少工件重复装夹，提高加精度和效率。角头主要用于中心镗铣床等，可以装在刀库中并和机床主轴之间实现自动换。本次毕业设计是进行角度头的三维模型建立，并进行运动仿真及结构分析具体参数为：输出轴与输入轴成 45 °，输出最大扭矩10Nm ，最高转速2000r/min，刀柄形式为BT40。 [关键字]：角度头、结构设计、运动仿真 Processing center 45° Angle head is designed and simulation [Abstract] Angle head is a machine tool accessories. The placement of the centerline of rotation of the tool into the spindle center line the specified angle machining parts, without changing the machine tool structure can increase its scope and versatility and can reduce repeat work piece clamping, increase the added accuracy and efficiency. Angle head for the center boring and milling machine can be installed in the magazine and between the machine tool spindle wrap. The graduation project is the head angle three-dimensional model, and motion simulation and structural analysis of the specific parameters: the output shaft and the input shaft into a 45°maximum torque of 10nm, the maximum speed of 2000r/min holder in the form of BT40 . [Key words]: Angle head, motion simulation, structural analysis 目 录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc3593479771 绪论 1 HYPERLINK \l _Toc3593479781.1 角度头的定义 PAGEREF _Toc359347978 \h 1 HYPERLINK \l _Toc3593479791.2 角度头的分类 PAGEREF _Toc359347979 \h 1 HYPERLINK \l _Toc3593479801.3角度头应用场合及注意事项 PAGEREF _Toc359347980 \h 2 HYPERLINK \l _Toc3593479812 45度角度头的结构分析 PAGEREF _Toc359347981 \h 4 HYPERLINK \l _Toc3593479822.1 产品外形及内部结构 PAGEREF _Toc359347982 \h 4 HYPERLINK \l _Toc3593479832.2零件选型 PAGEREF _Toc359347983 \h 6 HYPERLINK \l _Toc3593479843 锥齿轮及齿轮轴的设计 PAGEREF _Toc359347984 \h 7 HYPERLINK \l _Toc3593479853.1锥齿轮的计算 PAGEREF _Toc359347985 \h 7 HYPERLINK \l _Toc3593479863.2齿轮轴的计算 PAGEREF _Toc359347986 \h 10 HYPERLINK \l _Toc3593479874 三维建模与仿真 PAGEREF _Toc359347987 \h 17 HYPERLINK \l _Toc3593479884.1锥齿轮建模（45度） PAGEREF _Toc359347988 \h 17 HYPERLINK \l _Toc3593479894.1.1锥齿轮简介 PAGEREF _Toc359347989 \h 17 HYPERLINK \l _Toc3593479904.1.2参数输入 PAG