创维彩电维修通病（Skyworth color TV repair and maintenance）.docVIP

下载本文档

16
0
约2万字
约 19页
2017-07-15 发布于河南
举报
版权申诉

创维彩电维修通病（Skyworth color TV repair and maintenance）.doc

1、本文档共19页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

创维彩电维修通病（Skyworth color TV repair and maintenance）

创维彩电维修通病（Skyworth color TV repair and maintenance） Crewmtv repair and maintenance I maintain a dozen of this machine, mostly red, sometimes not, is DA4544, V501 dissolder, others are also to be taken off, soldering will solve the problem. Basically every platform has this problem. The failure of skyworth 21TM9000 (3T30 machine heart) is like: when the cold machine is up, the temperature of the machine will be compressed. In the cold machine boot when the measured voltage is normal, but the engine out immediately after the 5-10 minutes of compression jitter, sawtooth voltage and measuring field block (9302) the third foot flyback input voltage is reduced, doubt is the 15 feet in the field of TMPA8823 sawtooth circuit capacitance C214 M0.47 (UF) metamorphism caused a sawtooth voltage reduce the jitter of out after the scene image compression, after replacement of the fault as a ruled out. Please give me a lot of advice if you dont write well! 3. The creation of 25NL5 minutes automatic shutdown, disconnection load failure unchanged. Check the perimeter of 6709. The power supply at normal time is 7.8 V. When the fault occurs, the power supply stops and the voltage of 9 feet drops to 6.8 V. After the belt change 66709 is invalid, the change of the shock capacitance also does not work, after using 2482 to change 1640, the fault is not in appearance, but when the test machine one hour, the failure appears again, after change the original outfit 1640 after the failure to rule out. The original 1640 was not damaged. And the problem of the problem of 1640 is that the usual fault phenomenon is the intermittent oscillations of power supply. 29TBDA [5D60] does not turn on, the indicator lights blink Open the shell and start, the main voltage measured between 30 ~ 140V. The internal relay is repeated. Break operation load, check the switch regulated power supply control circuit is normal, a switching power supply load capacity is also normal, judge fault was caused by abnormal li