数控车床法兰克系统常用循环指令（Numerical control lathe, Frank system, common cycle instruction）.doc

下载文档 降价啦

69
0
约1.11万字
约 13页
2017-07-24 发布于河南
举报
版权申诉
保障服务

数控车床法兰克系统常用循环指令（Numerical control lathe, Frank system, common cycle instruction）.doc

1、本文档共13页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

数控车床法兰克系统常用循环指令（Numerical control lathe, Frank system, common cycle instruction）

数控车床法兰克系统常用循环指令（Numerical control lathe, Frank system, common cycle instruction） [turning of rotating parts with increasing diameter] G71 U W R G71, P, Q, U, W, F Every time the feed back cutting depth U: W: usually not, or rarely R: amount of return P: specifies the start line of the loop instruction Q: Specifies the end of the loop instruction and the beginning of the program line U: X in the direction of the fine car margin W: Z in the direction of the fine car margin Feed speed of F: cycle rough car [with a groove, i.e., a large or small rotating workpiece when it is an outer circle.] G73 U W R G73, P, Q, U, W, F The difference between the maximum diameter and the minimum diameter of the U: part, divided by 2 W: usually not, or rarely R: the number of cycles, usually by materials, divided by U depth P: specifies the start line of the loop instruction Q: Specifies the end of the loop instruction and the beginning of the program line U: X in the direction of the fine car margin W: Z in the direction of the fine car margin Feed speed of F: cycle rough car [thread turning] G92, X, Z, R, F X: X value at each turn Z: turning length of thread R: when learning cone threads, the diameter of the path is subtracted by the diameter divided by 2, and in general it is a negative number F: thread pitch value G71 G72 G73 here, G71 is the most common G71 U1.5 R1 G71, P1, Q2, U0.5, W0.1, F200 ...... G70 P1 Q2 The omitted part is the contour program of turning The problem is mainly the difference between G71 and G72. G70 is the precise cycle of vehicles shared by G71 and G72. (that is, G71..... G70 or G72....... G70) G71 is the outer circle, rough vehicle cycle (along the X axis feed, Z axis turning) G72 is the end face rough cycle (along the Z shaft feed, X axis turning) G71, G72 are left with fine machining margin, and then use G70 G71, G72 left margin off. When the FANUC machining center uses G84 to attack the thread, what is the speed and feed? The spindle revolutions = the pi