浮法玻璃操作(整理)（Float glass operation (finishing)）.docVIP

下载本文档

13
0
约 13页
2017-07-24 发布于河南
举报
版权申诉

浮法玻璃操作(整理)（Float glass operation (finishing)）.doc

1、本文档共13页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

浮法玻璃操作(整理)（Float glass operation (finishing)）

浮法玻璃操作(整理)（Float glass operation (finishing)） 1. what is called deep fry? Classification, causes and solutions of longitudinal blasting? Fried refers to the glass in the longitudinal lower limit of annealing temperature (450 degrees) above the edge of the glass temperature is higher than the middle temperature, or glass in the lower limit of annealing temperature (450 degrees) below the glass edge temperature is lower than the longitudinal edge of the glass burst intermediate temperature produces a tight and produce. Classification of blasting: permanent blasting caused by excessive permanent stress of glass: longitudinal stress caused by excessive temporary stress of glass; cause of longitudinal blasting and solution method; reason: too large tension at side. Solution: in the B and C areas, the A area, the B zone, the middle temperature, or the A area and the B zone edge temperature are increased. After the D section, the C area, R area, F zone, the middle temperature, or the temperature of the C, R and F areas are decreased. 2. what is called horizontal fried? Classification, causes and solutions of transverse blasting? Bombing refers to the glass in the lower limit of annealing temperature (450 degrees) above the edge of the glass temperature below the middle temperature, or glass in the lower limit of annealing temperature (450 DEG) lateral edge of the glass burst below the glass edge temperature is higher than the middle temperature than the loose generated. Another is that there is a large inclusion in the glass, roll bending, tin outlet temperature, glass deformation, or tin groove block The side edge of the wheel force caused by excessive large deformation caused by transverse crack of glass. Classification of transverse blasting: excessive stress caused by excessive permanent stress of glass, excessive stress caused by temporary blasting of glass, cause of transverse explosion, transverse explosion, and solution. Solution: in B, C burst occurred, increased