锥螺纹钢筋接头工艺标准(417-1996)（Standard for taper thread joint of steel bar (417-1996)）.docVIP

下载本文档

5
0
约1.15万字
约 12页
2017-07-24 发布于河南
举报
版权申诉

锥螺纹钢筋接头工艺标准(417-1996)（Standard for taper thread joint of steel bar (417-1996)）.doc

1、本文档共12页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

锥螺纹钢筋接头工艺标准(417-1996)（Standard for taper thread joint of steel bar (417-1996)）

锥螺纹钢筋接头工艺标准(417-1996)（Standard for taper thread joint of steel bar (417-1996)） Range The process standard is applicable to the connection of the same diameter or different diameter steel bars of grade 16 and 40mm in the cast-in-place reinforced concrete structure of industrial and civil buildings. The difference between the diameters of the connecting bars is not more than 9mm. The use of tapered threaded steel connections shall be approved by the designer. Construction preparation 2.1 materials and main equipment: 2.1.1 reinforcement: the grade and diameter of the reinforcement must comply with the design requirements. There is a factory certificate and a re examination report. The 2.1.2 connection sleeve shall meet the following requirements: 2.1.2.1 has an obvious specification mark (such as 32 or 32). Sealed cover sealed with plastic cone 2.1.2.2. 2.1.2.3 same diameter or different diameter sleeve size in table 4-25 of the specified range. Connecting sleeve specification size table 4-25 Connecting sleeve specification mark outer diameter not less than (mm) length is not less than (mm) 16, 16, 25-0.5, 65-0.5 18, 18, 28-0.5, 75-0.5 20, 20, 30-0.5, 85-0.5 22, 22, 32-0.5, 95-0.5 25, 25, 35-0.5, 95-0.5 28, 28, 39-0.5, 105-0.5 32, 32, 44-0.5, 115-0.5 36, 36, 48-0.5, 125-0.5 40, 40, 52-0.5, 135-0.5 2.1.2.4 cone thread screw in the connecting sleeve, the connecting sleeve should be in the end edge of the notch range within the cone thread end (Figure 4-36). Figure 4-36 2.1.2.5 has a product qualification certificate. 2.1.2.6 connection sleeves shall be classified, packaged and stored, and shall not be confused or rusted. 2.1.3 main tools: 2.1.3.1 steel wire binding machine: model SZ, 50A, or other sets of diameter of 16mm and above the second and third class rebar wire machine. 2.1.3.2: including tooth gauge gauge gage, calipers and taper thread plug gauge. A dental gauge is a gauge used to inspect the quality of taper thread shaping of the ends of reinforcing bars. The