引起互调干扰的器件介绍2（Introduction to intermodulation interference devices 2）.doc

下载文档 降价啦

6
0
约10千字
约 10页
2017-07-24 发布于河南
举报
版权申诉
保障服务

引起互调干扰的器件介绍2（Introduction to intermodulation interference devices 2）.doc

1、本文档共10页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

引起互调干扰的器件介绍2（Introduction to intermodulation interference devices 2）

引起互调干扰的器件介绍2（Introduction to intermodulation interference devices 2） Two cm differential loss 3.2dBm power sharing Three points differential loss, 5dBm power three points 5dB coupler through end differential loss 1.8dBm 6dB coupler through end differential loss 1.4dBm 7dB coupler through end differential loss 1.2dBm 10dB coupler through end differential loss 0.5dBm 15dB coupler through end differential loss 0.3dBm 20dB coupler through end differential loss 0.2dBm The allocation is based on the size of the coupler, such as the 5dB coupler, the coupling end output = the input -5dBm, the through end output = the input differential loss The coupler is acting exactly the opposite of the combiner. The coupler is used at the receiving end and the combiner is used for the transmitter. The coupler divides the received radio signals into several different receivers, and the combiner combines several radio signals from different transmitters to transmit them to the antenna. The coupler has 4 ports and also has 3 ports. In fact, the two in principle and structure is the same, the reason why the emergence of 3 port coupler, because in the 4 port coupler, one of the coupling end with a load, so that it becomes three port. Take the 4 port coupler as an example, each port has the following name: RF-INPUT radio frequency signal input terminal, RF-OUTPUT RF signal output end, COUPLED FORWARD forward coupling end, and COUPLED ERVERSE back coupling end. Take 15dB four port coupler as an example: The 0dBm signal is input from the RF-INPUT, and the power at each other port is: RF-OUTPUT -1.2dBm COUPLED FORWARD -15dBm COUPLED ERVERSE -35dBm The 0dBm signal is input from the RF-OUTPUT, and the power at each other port is: RF-INPUT -1.2dBm COUPLED FORWARD -35dBm COUPLED ERVERSE -15dBm The 0dBm signal is input from the COUPLED FORWARD, and the power obtained at each other port is: COUPLED ERVERSE -1.2dBm RF-INPUT -15dBm RF-OUTPUT -35dBm The 0dBm signal is input from the COUPLED ERVERSE, and