聚乙烯丙纶防水施工（Waterproof construction of polyethylene polypropylene fiber）.docVIP

下载本文档

4
0
约1.02万字
约 8页
2017-07-24 发布于河南
举报
版权申诉

聚乙烯丙纶防水施工（Waterproof construction of polyethylene polypropylene fiber）.doc

1、本文档共8页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

聚乙烯丙纶防水施工（Waterproof construction of polyethylene polypropylene fiber）

聚乙烯丙纶防水施工（Waterproof construction of polyethylene polypropylene fiber） Construction operation procedure Acceptance of the basic level: sweep to the construction layer to configure the viscosity (with the use of configuration) - to deal with complex parts - waterproof layer (or gas barrier) - Construction - Test - protection layer construction - acceptance. Two 、 construction preparation (material preparation, including water, cement, rubber powder): Serial number, name, specification, unit, quantity, remark 1 brush 40mm 2 2 scraper 30mm 3 hard rubber 3 mixing appliance, 2 electric mixer or hard bamboo handle 4 glue container is greater than or equal to 100 or 2 according to the materials available half barrels 5 1 ordinary civil scissors 6 knives, 2 wallpaper knives 7 cleaning tools, depending on the broom or shovel 8 scale with 50 kg 110 Taiwan 9, greasy knife 30mm, 2 should use special applicator Three, construction procedures and methods: 3.1 leveling layer construction quality should comply with the level of engineering technical specifications (GB50345-2004) regulations. 3.2 leveling layer should be conducive to the development and application of coil paste; the leveling layer should be smooth pressure light, smooth and clean surface, no cracking, Jiecha formation. No obvious sharp, convex, concave, peeling and sand lifting are allowed. The leveling layer should be changed gently within the allowable range, the slope is uniform and the slope is the same, and it conforms to the design requirements of the drawing. 3.3 flat roof eaves gutter, eaves gutter, leveling layer slope must meet the design requirements. With 3.4 leveling layer and the facade structure (parapet, chimneys, vents, cracks, wall skylight etc.) are coved. Not less than 5%. 3.5 longitudinal slope, surrounding drainage outfall should be made slightly at the bottom of the pit. 3.6 adhesives use special glue (first made of special rubber powder and water) and cement mixed cement pulp. Note that alre