液晶高压板维修与代换（Maintenance and substitution of liquid crystal high voltage plate）.docVIP

下载本文档

2
0
约1.18万字
约 9页
2017-08-02 发布于河南
举报
版权申诉

液晶高压板维修与代换（Maintenance and substitution of liquid crystal high voltage plate）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

液晶高压板维修与代换（Maintenance and substitution of liquid crystal high voltage plate） Repair LCD high-pressure plate fault is a headache, especially the difficult fault or with less than the corresponding pressure plate when the first two big, but not as scrap or retreat, that no face, in fact, people are living, as long as any pressure plate installed, then it is universal. Do not know the parameters to buy high pressure plate, pressure plate to see so many interface lines, dizziness. In fact, very simple, first determine the power line positive and negative, there is a fuse in general is the positive pole, the negative electrode is connected to the negative electrode of the capacitor. Then the best way to determine the voltage, voltage is determined to see if the capacitance of the mark, it is about 6V 3.3V, if the capacitor superscript around 12V, so the input voltage is 5V, if it is 24V or above, there is a 12V, and so on, the standard capacitor volt number by two, the closest a few volts is a few volts. Some people say, according to this answer, or not bright, or just flash it out, yes, there are many high-pressure board is more like this, then what should I do? Find out the control at the foot, foot is receiving a small transistor on the general is directly connected to a transistor, up to the middle of a small capacitor should be easy to recognize, control foot is generally 3.3V and 5V, there are also individual is grounded, so we dont know. Under the condition of grounding, first try not to pick up 3.3V and then 5V, if the input voltage and the control voltage is more than 3.3V, can be directly combined. What about the excess feet? Leave him alone, and leave him alone. After the high-pressure plate is broken, the most common are the following faults: 1, instant light immediately black screen The main problem for high voltage board feedback circuit plays the role of lead, such as: high voltage feedback circuit protection, lead to problems resulting in no feedback vol